In the Linux kernel, the following vulnerability has been resolved:
can: j1939: prevent deadlock by changing j1939_socks_lock to rwlock
The following 3 locks would race against each other, causing the
deadlock situation in the Syzbot bug report:
- j1939_socks_lock
- active_session_list_lock
- sk_session_queue_lock
A reasonable fix is to change j1939_socks_lock to an rwlock, since in
the rare situations where a write lock is required for the linked list
that j1939_socks_lock is protecting, the code does not attempt to
acquire any more locks. This would break the circular lock dependency,
where, for example, the current thread already locks j1939_socks_lock
and attempts to acquire sk_session_queue_lock, and at the same time,
another thread attempts to acquire j1939_socks_lock while holding
sk_session_queue_lock.
NOTE: This patch along does not fix the unregister_netdevice bug
reported by Syzbot; instead, it solves a deadlock situation to prepare
for one or more further patches to actually fix the Syzbot bug, which
appears to be a reference counting problem within the j1939 codebase.
[mkl: remove unrelated newline change]
In the Linux kernel, the following vulnerability has been resolved:
blk-mq: fix IO hang from sbitmap wakeup race
In blk_mq_mark_tag_wait(), __add_wait_queue() may be re-ordered
with the following blk_mq_get_driver_tag() in case of getting driver
tag failure.
Then in __sbitmap_queue_wake_up(), waitqueue_active() may not observe
the added waiter in blk_mq_mark_tag_wait() and wake up nothing, meantime
blk_mq_mark_tag_wait() can't get driver tag successfully.
This issue can be reproduced by running the following test in loop, and
fio hang can be observed in < 30min when running it on my test VM
in laptop.
modprobe -r scsi_debug
modprobe scsi_debug delay=0 dev_size_mb=4096 max_queue=1 host_max_queue=1 submit_queues=4
dev=`ls -d /sys/bus/pseudo/drivers/scsi_debug/adapter*/host*/target*/*/block/* | head -1 | xargs basename`
fio --filename=/dev/"$dev" --direct=1 --rw=randrw --bs=4k --iodepth=1 \
--runtime=100 --numjobs=40 --time_based --name=test \
--ioengine=libaio
Fix the issue by adding one explicit barrier in blk_mq_mark_tag_wait(), which
is just fine in case of running out of tag.
In the Linux kernel, the following vulnerability has been resolved:
xhci: handle isoc Babble and Buffer Overrun events properly
xHCI 4.9 explicitly forbids assuming that the xHC has released its
ownership of a multi-TRB TD when it reports an error on one of the
early TRBs. Yet the driver makes such assumption and releases the TD,
allowing the remaining TRBs to be freed or overwritten by new TDs.
The xHC should also report completion of the final TRB due to its IOC
flag being set by us, regardless of prior errors. This event cannot
be recognized if the TD has already been freed earlier, resulting in
"Transfer event TRB DMA ptr not part of current TD" error message.
Fix this by reusing the logic for processing isoc Transaction Errors.
This also handles hosts which fail to report the final completion.
Fix transfer length reporting on Babble errors. They may be caused by
device malfunction, no guarantee that the buffer has been filled.
In the Linux kernel, the following vulnerability has been resolved:
um: time-travel: fix time corruption
In 'basic' time-travel mode (without =inf-cpu or =ext), we
still get timer interrupts. These can happen at arbitrary
points in time, i.e. while in timer_read(), which pushes
time forward just a little bit. Then, if we happen to get
the interrupt after calculating the new time to push to,
but before actually finishing that, the interrupt will set
the time to a value that's incompatible with the forward,
and we'll crash because time goes backwards when we do the
forwarding.
Fix this by reading the time_travel_time, calculating the
adjustment, and doing the adjustment all with interrupts
disabled.
In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Fix disable_otg_wa logic
[Why]
When switching to another HDMI mode, we are unnecesarilly
disabling/enabling FIFO causing both HPO and DIG registers to be set at
the same time when only HPO is supposed to be set.
This can lead to a system hang the next time we change refresh rates as
there are cases when we don't disable OTG/FIFO but FIFO is enabled when
it isn't supposed to be.
[How]
Removing the enable/disable FIFO entirely.
In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Fix late derefrence 'dsc' check in 'link_set_dsc_pps_packet()'
In link_set_dsc_pps_packet(), 'struct display_stream_compressor *dsc'
was dereferenced in a DC_LOGGER_INIT(dsc->ctx->logger); before the 'dsc'
NULL pointer check.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/../display/dc/link/link_dpms.c:905 link_set_dsc_pps_packet() warn: variable dereferenced before check 'dsc' (see line 903)