In the Linux kernel, the following vulnerability has been resolved:
arm64: dts: qcom: qcs615: fix a crash issue caused by infinite loop for Coresight
An infinite loop has been created by the Coresight devices. When only a
source device is enabled, the coresight_find_activated_sysfs_sink function
is recursively invoked in an attempt to locate an active sink device,
ultimately leading to a stack overflow and system crash. Therefore, disable
the replicator1 to break the infinite loop and prevent a potential stack
overflow.
replicator1_out -> funnel_swao_in6 -> tmc_etf_swao_in -> tmc_etf_swao_out
| |
replicator1_in replicator_swao_in
| |
replicator0_out1 replicator_swao_out0
| |
replicator0_in funnel_in1_in3
| |
tmc_etf_out <- tmc_etf_in <- funnel_merg_out <- funnel_merg_in1 <- funnel_in1_out
[call trace]
dump_backtrace+0x9c/0x128
show_stack+0x20/0x38
dump_stack_lvl+0x48/0x60
dump_stack+0x18/0x28
panic+0x340/0x3b0
nmi_panic+0x94/0xa0
panic_bad_stack+0x114/0x138
handle_bad_stack+0x34/0xb8
__bad_stack+0x78/0x80
coresight_find_activated_sysfs_sink+0x28/0xa0 [coresight]
coresight_find_activated_sysfs_sink+0x5c/0xa0 [coresight]
coresight_find_activated_sysfs_sink+0x5c/0xa0 [coresight]
coresight_find_activated_sysfs_sink+0x5c/0xa0 [coresight]
coresight_find_activated_sysfs_sink+0x5c/0xa0 [coresight]
...
coresight_find_activated_sysfs_sink+0x5c/0xa0 [coresight]
coresight_enable_sysfs+0x80/0x2a0 [coresight]
side effect after the change:
Only trace data originating from AOSS can reach the ETF_SWAO and EUD sinks.
In the Linux kernel, the following vulnerability has been resolved:
landlock: Fix warning from KUnit tests
get_id_range() expects a positive value as first argument but
get_random_u8() can return 0. Fix this by clamping it.
Validated by running the test in a for loop for 1000 times.
Note that MAX() is wrong as it is only supposed to be used for
constants, but max() is good here.
[..] ok 9 test_range2_rand1
[..] ok 10 test_range2_rand2
[..] ok 11 test_range2_rand15
[..] ------------[ cut here ]------------
[..] WARNING: CPU: 6 PID: 104 at security/landlock/id.c:99 test_range2_rand16 (security/landlock/id.c:99 (discriminator 1) security/landlock/id.c:234 (discriminator 1))
[..] Modules linked in:
[..] CPU: 6 UID: 0 PID: 104 Comm: kunit_try_catch Tainted: G N 6.16.0-rc1-dev-00001-g314a2f98b65f #1 PREEMPT(undef)
[..] Tainted: [N]=TEST
[..] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2 04/01/2014
[..] RIP: 0010:test_range2_rand16 (security/landlock/id.c:99 (discriminator 1) security/landlock/id.c:234 (discriminator 1))
[..] Code: 49 c7 c0 10 70 30 82 4c 89 ff 48 c7 c6 a0 63 1e 83 49 c7 45 a0 e0 63 1e 83 e8 3f 95 17 00 e9 1f ff ff ff 0f 0b e9 df fd ff ff <0f> 0b ba 01 00 00 00 e9 68 fe ff ff 49 89 45 a8 49 8d 4d a0 45 31
[..] RSP: 0000:ffff888104eb7c78 EFLAGS: 00010246
[..] RAX: 0000000000000000 RBX: 000000000870822c RCX: 0000000000000000
^^^^^^^^^^^^^^^^
[..]
[..] Call Trace:
[..]
[..] ---[ end trace 0000000000000000 ]---
[..] ok 12 test_range2_rand16
[..] # landlock_id: pass:12 fail:0 skip:0 total:12
[..] # Totals: pass:12 fail:0 skip:0 total:12
[..] ok 1 landlock_id
[mic: Minor cosmetic improvements]
In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: btusb: Fix potential NULL dereference on kmalloc failure
Avoid potential NULL pointer dereference by checking the return value of
kmalloc and handling allocation failure properly.
In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: fix WARN_ON for monitor mode on some devices
On devices without WANT_MONITOR_VIF (and probably without
channel context support) we get a WARN_ON for changing the
per-link setting of a monitor interface.
Since we already skip AP_VLAN interfaces and MONITOR with
WANT_MONITOR_VIF and/or NO_VIRTUAL_MONITOR should update
the settings, catch this in the link change code instead
of the warning.
In the Linux kernel, the following vulnerability has been resolved:
pinmux: fix race causing mux_owner NULL with active mux_usecount
commit 5a3e85c3c397 ("pinmux: Use sequential access to access
desc->pinmux data") tried to address the issue when two client of the
same gpio calls pinctrl_select_state() for the same functionality, was
resulting in NULL pointer issue while accessing desc->mux_owner.
However, issue was not completely fixed due to the way it was handled
and it can still result in the same NULL pointer.
The issue occurs due to the following interleaving:
cpu0 (process A) cpu1 (process B)
pin_request() { pin_free() {
mutex_lock()
desc->mux_usecount--; //becomes 0
..
mutex_unlock()
mutex_lock(desc->mux)
desc->mux_usecount++; // becomes 1
desc->mux_owner = owner;
mutex_unlock(desc->mux)
mutex_lock(desc->mux)
desc->mux_owner = NULL;
mutex_unlock(desc->mux)
This sequence leads to a state where the pin appears to be in use
(`mux_usecount == 1`) but has no owner (`mux_owner == NULL`), which can
cause NULL pointer on next pin_request on the same pin.
Ensure that updates to mux_usecount and mux_owner are performed
atomically under the same lock. Only clear mux_owner when mux_usecount
reaches zero and no new owner has been assigned.
In the Linux kernel, the following vulnerability has been resolved:
clk: spacemit: mark K1 pll1_d8 as critical
The pll1_d8 clock is enabled by the boot loader, and is ultimately a
parent for numerous clocks, including those used by APB and AXI buses.
Guodong Xu discovered that this clock got disabled while responding to
getting -EPROBE_DEFER when requesting a reset controller.
The needed clock (CLK_DMA, along with its parents) had already been
enabled. To respond to the probe deferral return, the CLK_DMA clock
was disabled, and this led to parent clocks also reducing their enable
count. When the enable count for pll1_d8 was decremented it became 0,
which caused it to be disabled. This led to a system hang.
Marking that clock critical resolves this by preventing it from being
disabled.
Define a new macro CCU_FACTOR_GATE_DEFINE() to allow clock flags to
be supplied for a CCU_FACTOR_GATE clock.
In the Linux kernel, the following vulnerability has been resolved:
rv: Use strings in da monitors tracepoints
Using DA monitors tracepoints with KASAN enabled triggers the following
warning:
BUG: KASAN: global-out-of-bounds in do_trace_event_raw_event_event_da_monitor+0xd6/0x1a0
Read of size 32 at addr ffffffffaada8980 by task ...
Call Trace:
<TASK>
[...]
do_trace_event_raw_event_event_da_monitor+0xd6/0x1a0
? __pfx_do_trace_event_raw_event_event_da_monitor+0x10/0x10
? trace_event_sncid+0x83/0x200
trace_event_sncid+0x163/0x200
[...]
The buggy address belongs to the variable:
automaton_snep+0x4e0/0x5e0
This is caused by the tracepoints reading 32 bytes __array instead of
__string from the automata definition. Such strings are literals and
reading 32 bytes ends up in out of bound memory accesses (e.g. the next
automaton's data in this case).
The error is harmless as, while printing the string, we stop at the null
terminator, but it should still be fixed.
Use the __string facilities while defining the tracepoints to avoid
reading out of bound memory.