Linux: >> Linux Kernel >> 3.16.46 Security Vulnerabilities
In the Linux kernel, the following vulnerability has been resolved:
8021q: delete cleared egress QoS mappings
vlan_dev_set_egress_priority() currently keeps cleared egress
priority mappings in the hash as tombstones. Repeated set/clear cycles
with distinct skb priorities therefore accumulate mapping nodes until
device teardown and leak memory.
Delete mappings when vlan_prio is cleared instead of keeping tombstones.
Now that the egress mapping lists are RCU protected, the node can be
unlinked safely and freed after a grace period.
CVSS Score
5.5
EPSS Score
0.001
Published
2026-05-28
In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_event: fix potential UAF in SSP passkey handlers
hci_conn lookup and field access must be covered by hdev lock in
hci_user_passkey_notify_evt() and hci_keypress_notify_evt(), otherwise
the connection can be freed concurrently.
Extend the hci_dev_lock critical section to cover all conn usage in both
handlers.
Keep the existing keypress notification behavior unchanged by routing
the early exits through a common unlock path.
CVSS Score
8.8
EPSS Score
0.003
Published
2026-05-27
In the Linux kernel, the following vulnerability has been resolved:
ALSA: ctxfi: Add fallback to default RSR for S/PDIF
spdif_passthru_playback_get_resources() uses atc->pll_rate as the RSR
for the MSR calculation loop. However, pll_rate is only updated in
atc_pll_init() and not in hw_pll_init(), so it remains 0 after the
card init.
When spdif_passthru_playback_setup() skips atc_pll_init() for
32000 Hz, (rsr * desc.msr) always becomes 0, causing the loop to spin
indefinitely.
Add fallback to use atc->rsr when atc->pll_rate is 0. This reflects
the hardware state, since hw_card_init() already configures the PLL
to the default RSR.
CVSS Score
5.5
EPSS Score
0.001
Published
2026-05-27
In the Linux kernel, the following vulnerability has been resolved:
md/raid5: fix soft lockup in retry_aligned_read()
When retry_aligned_read() encounters an overlapped stripe, it releases
the stripe via raid5_release_stripe() which puts it on the lockless
released_stripes llist. In the next raid5d loop iteration,
release_stripe_list() drains the stripe onto handle_list (since
STRIPE_HANDLE is set by the original IO), but retry_aligned_read()
runs before handle_active_stripes() and removes the stripe from
handle_list via find_get_stripe() -> list_del_init(). This prevents
handle_stripe() from ever processing the stripe to resolve the
overlap, causing an infinite loop and soft lockup.
Fix this by using __release_stripe() with temp_inactive_list instead
of raid5_release_stripe() in the failure path, so the stripe does not
go through the released_stripes llist. This allows raid5d to break out
of its loop, and the overlap will be resolved when the stripe is
eventually processed by handle_stripe().
CVSS Score
5.5
EPSS Score
0.001
Published
2026-05-27
In the Linux kernel, the following vulnerability has been resolved:
ceph: only d_add() negative dentries when they are unhashed
Ceph can call d_add(dentry, NULL) on a negative dentry that is already
present in the primary dcache hash.
In the current VFS that is not safe. d_add() goes through __d_add()
to __d_rehash(), which unconditionally reinserts dentry->d_hash into
the hlist_bl bucket. If the dentry is already hashed, reinserting the
same node can corrupt the bucket, including creating a self-loop.
Once that happens, __d_lookup() can spin forever in the hlist_bl walk,
typically looping only on the d_name.hash mismatch check and
eventually triggering RCU stall reports like this one:
rcu: INFO: rcu_sched self-detected stall on CPU
rcu: 87-....: (2100 ticks this GP) idle=3a4c/1/0x4000000000000000 softirq=25003319/25003319 fqs=829
rcu: (t=2101 jiffies g=79058445 q=698988 ncpus=192)
CPU: 87 UID: 2952868916 PID: 3933303 Comm: php-cgi8.3 Not tainted 6.18.17-i1-amd #950 NONE
Hardware name: Dell Inc. PowerEdge R7615/0G9DHV, BIOS 1.6.6 09/22/2023
RIP: 0010:__d_lookup+0x46/0xb0
Code: c1 e8 07 48 8d 04 c2 48 8b 00 49 89 fc 49 89 f5 48 89 c3 48 83 e3 fe 48 83 f8 01 77 0f eb 2d 0f 1f 44 00 00 48 8b 1b 48 85 db <74> 20 39 6b 18 75 f3 48 8d 7b 78 e8 ba 85 d0 00 4c 39 63 10 74 1f
RSP: 0018:ff745a70c8253898 EFLAGS: 00000282
RAX: ff26e470054cb208 RBX: ff26e470054cb208 RCX: 000000006e958966
RDX: ff26e48267340000 RSI: ff745a70c82539b0 RDI: ff26e458f74655c0
RBP: 000000006e958966 R08: 0000000000000180 R09: 9cd08d909b919a89
R10: ff26e458f74655c0 R11: 0000000000000000 R12: ff26e458f74655c0
R13: ff745a70c82539b0 R14: d0d0d0d0d0d0d0d0 R15: 2f2f2f2f2f2f2f2f
FS: 00007f5770896980(0000) GS:ff26e482c5d88000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f5764de50c0 CR3: 000000a72abb5001 CR4: 0000000000771ef0
PKRU: 55555554
Call Trace:
<TASK>
lookup_fast+0x9f/0x100
walk_component+0x1f/0x150
link_path_walk+0x20e/0x3d0
path_lookupat+0x68/0x180
filename_lookup+0xdc/0x1e0
vfs_statx+0x6c/0x140
vfs_fstatat+0x67/0xa0
__do_sys_newfstatat+0x24/0x60
do_syscall_64+0x6a/0x230
entry_SYSCALL_64_after_hwframe+0x76/0x7e
This is reachable with reused cached negative dentries. A Ceph lookup
or atomic_open can be handed a negative dentry that is already hashed,
and fs/ceph/dir.c then hits one of two paths that incorrectly assume
"negative" also means "unhashed":
- ceph_finish_lookup():
MDS reply is -ENOENT with no trace
-> d_add(dentry, NULL)
- ceph_lookup():
local ENOENT fast path for a complete directory with shared caps
-> d_add(dentry, NULL)
Both paths can therefore re-add an already-hashed negative dentry.
Ceph already uses the correct pattern elsewhere: ceph_fill_trace() only
calls d_add(dn, NULL) for a negative null-dentry reply when d_unhashed(dn)
is true.
Fix both fs/ceph/dir.c sites the same way: only call d_add() for a
negative dentry when it is actually unhashed. If the negative dentry
is already hashed, leave it in place and reuse it as-is.
This preserves the existing behavior for unhashed dentries while
avoiding d_hash list corruption for reused hashed negatives.
CVSS Score
7.5
EPSS Score
0.005
Published
2026-05-27
In the Linux kernel, the following vulnerability has been resolved:
mm: fix deferred split queue races during migration
migrate_folio_move() records the deferred split queue state from src and
replays it on dst. Replaying it after remove_migration_ptes(src, dst, 0)
makes dst visible before it is requeued, so a concurrent rmap-removal path
can mark dst partially mapped and trip the WARN in deferred_split_folio().
Move the requeue before remove_migration_ptes() so dst is back on the
deferred split queue before it becomes visible again.
Because migration still holds dst locked at that point, teach
deferred_split_scan() to requeue a folio when folio_trylock() fails.
Otherwise a fully mapped underused folio can be dequeued by the shrinker
and silently lost from split_queue.
[ziy@nvidia.com: move the comment]
CVSS Score
4.7
EPSS Score
0.001
Published
2026-05-27
In the Linux kernel, the following vulnerability has been resolved:
ALSA: usb-audio: stop parsing UAC2 rates at MAX_NR_RATES
parse_uac2_sample_rate_range() caps the number of enumerated
rates at MAX_NR_RATES, but it only breaks out of the current
rate loop. A malformed UAC2 RANGE response with additional
triplets continues parsing the remaining triplets and repeatedly
prints "invalid uac2 rates" while probe still holds
register_mutex.
Stop the whole parse once the cap is reached and return the
number of rates collected so far.
CVSS Score
5.5
EPSS Score
0.002
Published
2026-05-27
In the Linux kernel, the following vulnerability has been resolved:
misc: ibmasm: fix OOB MMIO read in ibmasm_handle_mouse_interrupt()
ibmasm_handle_mouse_interrupt() performs an out-of-bounds MMIO read
when the queue reader or writer index from hardware exceeds
REMOTE_QUEUE_SIZE (60).
A compromised service processor can trigger this by writing an
out-of-range value to the reader or writer MMIO register before
asserting an interrupt. Since writer is re-read from hardware on
every loop iteration, it can also be set to an out-of-range value
after the loop has already started.
The root cause is that get_queue_reader() and get_queue_writer() return
raw readl() values that are passed directly into get_queue_entry(),
which computes:
queue_begin + reader * sizeof(struct remote_input)
with no bounds check. This unchecked MMIO address is then passed to
memcpy_fromio(), reading 8 bytes from unintended device registers.
For sufficiently large values the address falls outside the PCI BAR
mapping entirely, triggering a machine check exception.
Fix by checking both indices against REMOTE_QUEUE_SIZE at the top of
the loop body, before any call to get_queue_entry(). On an out-of-range
value, reset the reader register to 0 via set_queue_reader() before
breaking, so that normal queue operation can resume if the corrupted
hardware state is transient.
CVSS Score
7.1
EPSS Score
0.001
Published
2026-05-27
In the Linux kernel, the following vulnerability has been resolved:
dm mirror: fix integer overflow in create_dirty_log()
The argument count calculation in create_dirty_log() performs
`*args_used = 2 + param_count` before validating against argc. When a
user provides a param_count close to UINT_MAX via the device mapper
table string, this unsigned addition wraps around to a small value,
causing the subsequent `argc < *args_used` check to be bypassed.
The overflowed param_count is then passed as argc to dm_dirty_log_create(),
where it can cause out-of-bounds reads on the argv array.
Fix by comparing param_count against argc - 2 before performing the
addition, following the same pattern used by parse_features() in the
same file. Since argc >= 2 is already guaranteed, the subtraction is
safe.
CVSS Score
5.5
EPSS Score
0.001
Published
2026-05-27
In the Linux kernel, the following vulnerability has been resolved:
libceph: Prevent potential null-ptr-deref in ceph_handle_auth_reply()
If a message of type CEPH_MSG_AUTH_REPLY contains a zero value for both
protocol and result, this is currently not treated as an error. In case
of ac->negotiating == true and ac->protocol > 0, this leads to setting
ac->protocol = 0 and ac->ops = NULL. Thereafter, the check for
ac->protocol != protocol returns false, and init_protocol() is not
called. Subsequently, ac->ops->handle_reply() is called, which leads to
a null pointer dereference, because ac->ops is still NULL.
This patch changes the check for ac->protocol != protocol to
!ac->protocol, as this also includes the case when the protocol was set
to zero in the message. This causes the message to be treated as
containing a bad auth protocol.
CVSS Score
7.5
EPSS Score
0.005
Published
2026-05-27