In the Linux kernel, the following vulnerability has been resolved:
atm: fore200e: fix use-after-free in tasklets during device removal
When the PCA-200E or SBA-200E adapter is being detached, the fore200e
is deallocated. However, the tx_tasklet or rx_tasklet may still be running
or pending, leading to use-after-free bug when the already freed fore200e
is accessed again in fore200e_tx_tasklet() or fore200e_rx_tasklet().
One of the race conditions can occur as follows:
CPU 0 (cleanup) | CPU 1 (tasklet)
fore200e_pca_remove_one() | fore200e_interrupt()
fore200e_shutdown() | tasklet_schedule()
kfree(fore200e) | fore200e_tx_tasklet()
| fore200e-> // UAF
Fix this by ensuring tx_tasklet or rx_tasklet is properly canceled before
the fore200e is released. Add tasklet_kill() in fore200e_shutdown() to
synchronize with any pending or running tasklets. Moreover, since
fore200e_reset() could prevent further interrupts or data transfers,
the tasklet_kill() should be placed after fore200e_reset() to prevent
the tasklet from being rescheduled in fore200e_interrupt(). Finally,
it only needs to do tasklet_kill() when the fore200e state is greater
than or equal to FORE200E_STATE_IRQ, since tasklets are uninitialized
in earlier states. In a word, the tasklet_kill() should be placed in
the FORE200E_STATE_IRQ branch within the switch...case structure.
This bug was identified through static analysis.
In the Linux kernel, the following vulnerability has been resolved:
ASoC: qcom: q6asm: drop DSP responses for closed data streams
'Commit a354f030dbce ("ASoC: qcom: q6asm: handle the responses
after closing")' attempted to ignore DSP responses arriving
after a stream had been closed.
However, those responses were still handled, causing lockups.
Fix this by unconditionally dropping all DSP responses associated with
closed data streams.
In the Linux kernel, the following vulnerability has been resolved:
dpaa2-switch: validate num_ifs to prevent out-of-bounds write
The driver obtains sw_attr.num_ifs from firmware via dpsw_get_attributes()
but never validates it against DPSW_MAX_IF (64). This value controls
iteration in dpaa2_switch_fdb_get_flood_cfg(), which writes port indices
into the fixed-size cfg->if_id[DPSW_MAX_IF] array. When firmware reports
num_ifs >= 64, the loop can write past the array bounds.
Add a bound check for num_ifs in dpaa2_switch_init().
dpaa2_switch_fdb_get_flood_cfg() appends the control interface (port
num_ifs) after all matched ports. When num_ifs == DPSW_MAX_IF and all
ports match the flood filter, the loop fills all 64 slots and the control
interface write overflows by one entry.
The check uses >= because num_ifs == DPSW_MAX_IF is also functionally
broken.
build_if_id_bitmap() silently drops any ID >= 64:
if (id[i] < DPSW_MAX_IF)
bmap[id[i] / 64] |= ...
In the Linux kernel, the following vulnerability has been resolved:
drm/amdkfd: Fix out-of-bounds write in kfd_event_page_set()
The kfd_event_page_set() function writes KFD_SIGNAL_EVENT_LIMIT * 8
bytes via memset without checking the buffer size parameter. This allows
unprivileged userspace to trigger an out-of bounds kernel memory write
by passing a small buffer, leading to potential privilege
escalation.
In the Linux kernel, the following vulnerability has been resolved:
dm mpath: Add missing dm_put_device when failing to get scsi dh name
When commit fd81bc5cca8f ("scsi: device_handler: Return error pointer in
scsi_dh_attached_handler_name()") added code to fail parsing the path if
scsi_dh_attached_handler_name() failed with -ENOMEM, it didn't clean up
the reference to the path device that had just been taken. Fix this, and
steamline the error paths of parse_path() a little.
In the Linux kernel, the following vulnerability has been resolved:
nfsd: fix nfs4_file refcount leak in nfsd_get_dir_deleg()
Claude pointed out that there is a nfs4_file refcount leak in
nfsd_get_dir_deleg(). Ensure that the reference to "fp" is released
before returning.
In the Linux kernel, the following vulnerability has been resolved:
net: consume xmit errors of GSO frames
udpgro_frglist.sh and udpgro_bench.sh are the flakiest tests
currently in NIPA. They fail in the same exact way, TCP GRO
test stalls occasionally and the test gets killed after 10min.
These tests use veth to simulate GRO. They attach a trivial
("return XDP_PASS;") XDP program to the veth to force TSO off
and NAPI on.
Digging into the failure mode we can see that the connection
is completely stuck after a burst of drops. The sender's snd_nxt
is at sequence number N [1], but the receiver claims to have
received (rcv_nxt) up to N + 3 * MSS [2]. Last piece of the puzzle
is that senders rtx queue is not empty (let's say the block in
the rtx queue is at sequence number N - 4 * MSS [3]).
In this state, sender sends a retransmission from the rtx queue
with a single segment, and sequence numbers N-4*MSS:N-3*MSS [3].
Receiver sees it and responds with an ACK all the way up to
N + 3 * MSS [2]. But sender will reject this ack as TCP_ACK_UNSENT_DATA
because it has no recollection of ever sending data that far out [1].
And we are stuck.
The root cause is the mess of the xmit return codes. veth returns
an error when it can't xmit a frame. We end up with a loss event
like this:
-------------------------------------------------
| GSO super frame 1 | GSO super frame 2 |
|-----------------------------------------------|
| seg | seg | seg | seg | seg | seg | seg | seg |
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 |
-------------------------------------------------
x ok ok <ok>| ok ok ok <x>
\\
snd_nxt
"x" means packet lost by veth, and "ok" means it went thru.
Since veth has TSO disabled in this test it sees individual segments.
Segment 1 is on the retransmit queue and will be resent.
So why did the sender not advance snd_nxt even tho it clearly did
send up to seg 8? tcp_write_xmit() interprets the return code
from the core to mean that data has not been sent at all. Since
TCP deals with GSO super frames, not individual segment the crux
of the problem is that loss of a single segment can be interpreted
as loss of all. TCP only sees the last return code for the last
segment of the GSO frame (in <> brackets in the diagram above).
Of course for the problem to occur we need a setup or a device
without a Qdisc. Otherwise Qdisc layer disconnects the protocol
layer from the device errors completely.
We have multiple ways to fix this.
1) make veth not return an error when it lost a packet.
While this is what I think we did in the past, the issue keeps
reappearing and it's annoying to debug. The game of whack
a mole is not great.
2) fix the damn return codes
We only talk about NETDEV_TX_OK and NETDEV_TX_BUSY in the
documentation, so maybe we should make the return code from
ndo_start_xmit() a boolean. I like that the most, but perhaps
some ancient, not-really-networking protocol would suffer.
3) make TCP ignore the errors
It is not entirely clear to me what benefit TCP gets from
interpreting the result of ip_queue_xmit()? Specifically once
the connection is established and we're pushing data - packet
loss is just packet loss?
4) this fix
Ignore the rc in the Qdisc-less+GSO case, since it's unreliable.
We already always return OK in the TCQ_F_CAN_BYPASS case.
In the Qdisc-less case let's be a bit more conservative and only
mask the GSO errors. This path is taken by non-IP-"networks"
like CAN, MCTP etc, so we could regress some ancient thing.
This is the simplest, but also maybe the hackiest fix?
Similar fix has been proposed by Eric in the past but never committed
because original reporter was working with an OOT driver and wasn't
providing feedback (see Link).
In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: validate user queue size constraints
Add validation to ensure user queue sizes meet hardware requirements:
- Size must be a power of two for efficient ring buffer wrapping
- Size must be at least AMDGPU_GPU_PAGE_SIZE to prevent undersized allocations
This prevents invalid configurations that could lead to GPU faults or
unexpected behavior.
In the Linux kernel, the following vulnerability has been resolved:
soc: ti: pruss: Fix double free in pruss_clk_mux_setup()
In the pruss_clk_mux_setup(), the devm_add_action_or_reset() indirectly
calls pruss_of_free_clk_provider(), which calls of_node_put(clk_mux_np)
on the error path. However, after the devm_add_action_or_reset()
returns, the of_node_put(clk_mux_np) is called again, causing a double
free.
Fix by returning directly, to avoid the duplicate of_node_put().
In the Linux kernel, the following vulnerability has been resolved:
netconsole: avoid OOB reads, msg is not nul-terminated
msg passed to netconsole from the console subsystem is not guaranteed
to be nul-terminated. Before recent
commit 7eab73b18630 ("netconsole: convert to NBCON console infrastructure")
the message would be placed in printk_shared_pbufs, a static global
buffer, so KASAN had harder time catching OOB accesses. Now we see:
printk: console [netcon_ext0] enabled
BUG: KASAN: slab-out-of-bounds in string+0x1f7/0x240
Read of size 1 at addr ffff88813b6d4c00 by task pr/netcon_ext0/594
CPU: 65 UID: 0 PID: 594 Comm: pr/netcon_ext0 Not tainted 6.19.0-11754-g4246fd6547c9
Call Trace:
kasan_report+0xe4/0x120
string+0x1f7/0x240
vsnprintf+0x655/0xba0
scnprintf+0xba/0x120
netconsole_write+0x3fe/0xa10
nbcon_emit_next_record+0x46e/0x860
nbcon_kthread_func+0x623/0x750
Allocated by task 1:
nbcon_alloc+0x1ea/0x450
register_console+0x26b/0xe10
init_netconsole+0xbb0/0xda0
The buggy address belongs to the object at ffff88813b6d4000
which belongs to the cache kmalloc-4k of size 4096
The buggy address is located 0 bytes to the right of
allocated 3072-byte region [ffff88813b6d4000, ffff88813b6d4c00)