On Juniper Networks EX4300 Series, receipt of a stream of specific IPv4 packets can cause Routing Engine (RE) high CPU load, which could lead to network protocol operation issue and traffic interruption. This specific packets can originate only from within the broadcast domain where the device is connected. This issue occurs when the packets enter to the IRB interface. Only IPv4 packets can trigger this issue. IPv6 packets cannot trigger this issue. This issue affects Juniper Networks Junos OS on EX4300 series: 17.3 versions prior to 17.3R3-S9; 17.4 versions prior to 17.4R2-S11, 17.4R3-S2; 18.1 versions prior to 18.1R3-S10; 18.2 versions prior to 18.2R3-S4; 18.3 versions prior to 18.3R2-S4, 18.3R3-S2; 18.4 versions prior to 18.4R2-S4, 18.4R3-S2; 19.1 versions prior to 19.1R2-S2, 19.1R3-S1; 19.2 versions prior to 19.2R1-S5, 19.2R2-S1, 19.2R3; 19.3 versions prior to 19.3R2-S4, 19.3R3; 19.4 versions prior to 19.4R1-S3, 19.4R2; 20.1 versions prior to 20.1R1-S3, 20.1R2.
CVSS Score
6.5
EPSS Score
0.002
Published
2020-10-16
When a device running Juniper Networks Junos OS with MPC7, MPC8, or MPC9 line cards installed and the system is configured for inline IP reassembly, used by L2TP, MAP-E, GRE, and IPIP, the packet forwarding engine (PFE) will become disabled upon receipt of large packets requiring fragmentation, generating the following error messages: [LOG: Err] MQSS(0): WO: Packet Error - Error Packets 1, Connection 29 [LOG: Err] eachip_hmcif_rx_intr_handler(7259): EA[0:0]: HMCIF Rx: Injected checksum error detected on WO response - Chunk Address 0x0 [LOG: Err] MQSS(0): DRD: RORD1: CMD reorder ID error - Command 11, Reorder ID 1838, QID 0 [LOG: Err] MQSS(0): DRD: UNROLL0: HMC chunk length error in stage 5 - Chunk Address: 0x4321f3 [LOG: Err] MQSS(0): DRD: UNROLL0: HMC chunk address error in stage 5 - Chunk Address: 0x0 [LOG: Notice] Error: /fpc/8/pfe/0/cm/0/MQSS(0)/0/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc), scope: pfe, category: functional, severity: major, module: MQSS(0), type: DRD_RORD_ENG_INT: CMD FSM State Error [LOG: Notice] Performing action cmalarm for error /fpc/8/pfe/0/cm/0/MQSS(0)/0/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(0) with scope: pfe category: functional level: major [LOG: Notice] Performing action get-state for error /fpc/8/pfe/0/cm/0/MQSS(0)/0/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(0) with scope: pfe category: functional level: major [LOG: Notice] Performing action disable-pfe for error /fpc/8/pfe/0/cm/0/MQSS(0)/0/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(0) with scope: pfe category: functional level: major By continuously sending fragmented packets that cannot be reassembled, an attacker can repeatedly disable the PFE causing a sustained Denial of Service (DoS). This issue affects Juniper Networks Junos OS: 17.2 versions prior to 17.2R3-S4 on MX Series; 17.3 versions prior to 17.3R3-S8 on MX Series; 17.4 versions prior to 17.4R2-S10, 17.4R3-S2 on MX Series; 18.1 versions prior to 18.1R3-S10 on MX Series; 18.2 versions prior to 18.2R3-S3 on MX Series; 18.2X75 versions prior to 18.2X75-D41, 18.2X75-D430, 18.2X75-D65 on MX Series; 18.3 versions prior to 18.3R1-S7, 18.3R2-S4, 18.3R3-S1 on MX Series; 18.4 versions prior to 18.4R1-S7, 18.4R2-S4, 18.4R3 on MX Series; 19.1 versions prior to 19.1R1-S5, 19.1R2-S1, 19.1R3 on MX Series; 19.2 versions prior to 19.2R1-S4, 19.2R2 on MX Series; 19.3 versions prior to 19.3R2-S2, 19.3R3 on MX Series. This issue is specific to inline IP reassembly, introduced in Junos OS 17.2. Versions of Junos OS prior to 17.2 are unaffected by this vulnerability.
CVSS Score
5.3
EPSS Score
0.003
Published
2020-07-17
On Juniper Networks SRX Series with ICAP (Internet Content Adaptation Protocol) redirect service enabled, a double free vulnerability can lead to a Denial of Service (DoS) or Remote Code Execution (RCE) due to processing of a specific HTTP message. Continued processing of this specific HTTP message may result in an extended Denial of Service (DoS). The offending HTTP message that causes this issue may originate both from the HTTP server or the client. This issue affects Juniper Networks Junos OS on SRX Series: 18.1 versions prior to 18.1R3-S9; 18.2 versions prior to 18.2R3-S3; 18.3 versions prior to 18.3R2-S4, 18.3R3-S1; 18.4 versions prior to 18.4R2-S5, 18.4R3; 19.1 versions prior to 19.1R2; 19.2 versions prior to 19.2R1-S2, 19.2R2; 19.3 versions prior to 19.3R2. This issue does not affect Juniper Networks Junos OS prior to 18.1R1.
CVSS Score
9.8
EPSS Score
0.02
Published
2020-07-17
When a device running Juniper Networks Junos OS with MPC7, MPC8, or MPC9 line cards installed and the system is configured for inline IP reassembly, used by L2TP, MAP-E, GRE, and IPIP, the packet forwarding engine (PFE) will become disabled upon receipt of small fragments requiring reassembly, generating the following error messages: [LOG: Err] MQSS(2): WO: Packet Error - Error Packets 1, Connection 29 [LOG: Err] eachip_hmcif_rx_intr_handler(7259): EA[2:0]: HMCIF Rx: Injected checksum error detected on WO response - Chunk Address 0x0 [LOG: Err] MQSS(2): DRD: RORD1: CMD reorder ID error - Command 11, Reorder ID 1960, QID 0 [LOG: Err] MQSS(2): DRD: UNROLL0: HMC chunk address error in stage 5 - Chunk Address: 0xc38fb1 [LOG: Notice] Error: /fpc/0/pfe/0/cm/0/MQSS(2)/2/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc), scope: pfe, category: functional, severity: major, module: MQSS(2), type: DRD_RORD_ENG_INT: CMD FSM State Error [LOG: Notice] Performing action cmalarm for error /fpc/0/pfe/0/cm/0/MQSS(2)/2/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(2) with scope: pfe category: functional level: major [LOG: Notice] Performing action get-state for error /fpc/0/pfe/0/cm/0/MQSS(2)/2/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(2) with scope: pfe category: functional level: major [LOG: Notice] Performing action disable-pfe for error /fpc/0/pfe/0/cm/0/MQSS(2)/2/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(2) with scope: pfe category: functional level: major By continuously sending fragmented packets that cannot be reassembled, an attacker can repeatedly disable the PFE causing a sustained Denial of Service (DoS). This issue affects Juniper Networks Junos OS: 17.2 versions prior to 17.2R3-S4 on MX Series; 17.3 versions prior to 17.3R3-S8 on MX Series; 17.4 versions prior to 17.4R2-S9, 17.4R3-S1 on MX Series; 18.1 versions prior to 18.1R3-S10 on MX Series; 18.2 versions prior to 18.2R2-S6, 18.2R3-S3 on MX Series; 18.2X75 versions prior to 18.2X75-D34, 18.2X75-D41, 18.2X75-D53, 18.2X75-D65, 18.2X75-D430 on MX Series; 18.3 versions prior to 18.3R1-S7, 18.3R2-S4, 18.3R3-S2 on MX Series; 18.4 versions prior to 18.4R1-S6, 18.4R2-S4, 18.4R3 on MX Series; 19.1 versions prior to 19.1R1-S4, 19.1R2-S1, 19.1R3 on MX Series; 19.2 versions prior to 19.2R1-S3, 19.2R2 on MX Series; 19.3 versions prior to 19.3R2-S2, 19.3R3 on MX Series. This issue is specific to inline IP reassembly, introduced in Junos OS 17.2. Versions of Junos OS prior to 17.2 are unaffected by this vulnerability.
CVSS Score
7.5
EPSS Score
0.004
Published
2020-07-17
On Juniper Networks Junos MX Series with service card configured, receipt of a stream of specific packets may crash the MS-PIC component on MS-MIC or MS-MPC. By continuously sending these specific packets, an attacker can repeatedly bring down MS-PIC on MS-MIC/MS-MPC causing a prolonged Denial of Service. This issue affects MX Series devices using MS-PIC, MS-MIC or MS-MPC service cards with any service configured. This issue affects Juniper Networks Junos OS on MX Series: 17.2R2-S7; 17.3R3-S4, 17.3R3-S5; 17.4R2-S4 and the subsequent SRs (17.4R2-S5, 17.4R2-S6, etc.); 17.4R3; 18.1R3-S3, 18.1R3-S4, 18.1R3-S5, 18.1R3-S6, 18.1R3-S7, 18.1R3-S8; 18.2R3, 18.2R3-S1, 18.2R3-S2; 18.3R2 and the SRs based on 18.3R2; 18.4R2 and the SRs based on 18.4R2; 19.1R1 and the SRs based on 19.1R1; 19.2R1 and the SRs based on 19.2R1; 19.3R1 and the SRs based on 19.3R1.
CVSS Score
7.5
EPSS Score
0.004
Published
2020-07-17
On Juniper Networks Junos OS devices, a stream of TCP packets sent to the Routing Engine (RE) may cause mbuf leak which can lead to Flexible PIC Concentrator (FPC) crash or the system to crash and restart (vmcore). This issue can be trigged by IPv4 or IPv6 and it is caused only by TCP packets. This issue is not related to any specific configuration and it affects Junos OS releases starting from 17.4R1. However, this issue does not affect Junos OS releases prior to 18.2R1 when Nonstop active routing (NSR) is configured [edit routing-options nonstop-routing]. The number of mbufs is platform dependent. The following command provides the number of mbufs counter that are currently in use and maximum number of mbufs that can be allocated on a platform: user@host> show system buffers 2437/3143/5580 mbufs in use (current/cache/total) Once the device runs out of mbufs, the FPC crashes or the vmcore occurs and the device might become inaccessible requiring a manual restart. This issue affects Juniper Networks Junos OS 17.4 versions prior to 17.4R2-S11, 17.4R3-S2; 18.1 versions prior to 18.1R3-S10; 18.2 versions prior to 18.2R2-S7, 18.2R3-S5; 18.2X75 versions prior to 18.2X75-D41, 18.2X75-D420.12, 18.2X75-D51, 18.2X75-D60, 18.2X75-D34; 18.3 versions prior to 18.3R2-S4, 18.3R3-S2; 18.4 versions prior to 18.4R1-S7, 18.4R2-S4, 18.4R3-S1; 19.1 versions prior to 19.1R1-S5, 19.1R2-S1, 19.1R3; 19.2 versions prior to 19.2R1-S5, 19.2R2; 19.3 versions prior to 19.3R2-S3, 19.3R3; 19.4 versions prior to 19.4R1-S2, 19.4R2. Versions of Junos OS prior to 17.4R1 are unaffected by this vulnerability.
CVSS Score
7.5
EPSS Score
0.005
Published
2020-07-17
On Juniper Networks SRX Series with ICAP (Internet Content Adaptation Protocol) redirect service enabled, processing a malformed HTTP message can lead to a Denial of Service (DoS) or Remote Code Execution (RCE) Continued processing of this malformed HTTP message may result in an extended Denial of Service (DoS) condition. The offending HTTP message that causes this issue may originate both from the HTTP server or the HTTP client. This issue affects Juniper Networks Junos OS on SRX Series: 18.1 versions prior to 18.1R3-S9 ; 18.2 versions prior to 18.2R2-S7, 18.2R3-S3; 18.3 versions prior to 18.3R1-S7, 18.3R2-S4, 18.3R3-S1; 18.4 versions prior to 18.4R1-S7, 18.4R2-S4, 18.4R3; 19.1 versions prior to 19.1R1-S5, 19.1R2; 19.2 versions prior to 19.2R1-S2, 19.2R2; 19.3 versions prior to 19.3R2. This issue does not affect Juniper Networks Junos OS prior to 18.1R1.
CVSS Score
9.8
EPSS Score
0.021
Published
2020-07-17
An improper use of a validation framework when processing incoming genuine BGP packets within Juniper Networks RPD (routing protocols process) daemon allows an attacker to crash RPD thereby causing a Denial of Service (DoS) condition. This framework requires these packets to be passed. By continuously sending any of these types of formatted genuine packets, an attacker can repeatedly crash the RPD process causing a sustained Denial of Service. Authentication to the BGP peer is not required. This issue can be initiated or propagated through eBGP and iBGP and can impact devices in either modes of use as long as the devices are configured to support the compromised framework and a BGP path is activated or active. This issue affects: Juniper Networks Junos OS 16.1 versions 16.1R7-S6 and later versions prior to 16.1R7-S8; 17.3 versions 17.3R2-S5, 17.3R3-S6 and later versions prior to 17.3R3-S8; 17.4 versions 17.4R2-S7, 17.4R3 and later versions prior to 17.4R2-S11, 17.4R3-S2; 18.1 versions 18.1R3-S7 and later versions prior to 18.1R3-S10; 18.2 versions 18.2R2-S6, 18.2R3-S2 and later versions prior to 18.2R2-S7, 18.2R3-S5; 18.2X75 versions 18.2X75-D12, 18.2X75-D32, 18.2X75-D33, 18.2X75-D51, 18.2X75-D60, 18.2X75-D411, 18.2X75-D420 and later versions prior to 18.2X75-D32, 18.2X75-D33, 18.2X75-D420, 18.2X75-D52, 18.2X75-D60, 18.2X75-D65, 18.2X75-D70;(*1) 18.3 versions 18.3R1-S6, 18.3R2-S3, 18.3R3 and later versions prior to 18.3R2-S4, 18.3R3-S2; 18.4 versions 18.4R1-S5, 18.4R2-S4, 18.4R3 and later versions prior to 18.4R1-S7, 18.4R2-S5, 18.4R3-S3(*2); 19.1 versions 19.1R1-S3, 19.1R2 and later versions prior to 19.1R1-S5, 19.1R2-S2, 19.1R3-S2; 19.2 versions 19.2R1-S2, 19.2R2 and later versions prior to 19.2R1-S5, 19.2R2, 19.2R3; 19.3 versions prior to 19.3R2-S3, 19.3R3; 19.4 versions prior to 19.4R1-S2, 19.4R2, 19.4R3; 20.1 versions prior to 20.1R1-S1, 20.1R2. This issue does not affect Junos OS prior to 16.1R1. This issue affects IPv4 and IPv6 traffic.
CVSS Score
7.5
EPSS Score
0.004
Published
2020-07-17
On Juniper Networks Junos OS and Junos OS Evolved devices, the receipt of a specific BGP UPDATE packet causes an internal counter to be incremented incorrectly, which over time can lead to the routing protocols process (RPD) crash and restart. This issue affects both IBGP and EBGP multihop deployment in IPv4 or IPv6 network. This issue affects: Juniper Networks Junos OS: 17.2X75 versions prior to 17.2X75-D105.19; 17.3 versions prior to 17.3R3-S8; 17.4 versions prior to 17.4R2-S10, 17.4R3-S2; 18.1 versions prior to 18.1R3-S10; 18.2 versions prior to 18.2R2-S7, 18.2R3-S4; 18.2X75 versions prior to 18.2X75-D13, 18.2X75-D411.1, 18.2X75-D420.18, 18.2X75-D52.3, 18.2X75-D60; 18.3 versions prior to 18.3R2-S4, 18.3R3-S2; 18.4 versions prior to 18.4R1-S7, 18.4R2-S4, 18.4R3-S2; 19.1 versions prior to 19.1R1-S5, 19.1R2-S1, 19.1R3; 19.2 versions prior to 19.2R1-S5, 19.2R2; 19.3 versions prior to 19.3R2-S2, 19.3R3; 19.4 versions prior to 19.4R1-S2, 19.4R2. Juniper Networks Junos OS Evolved: any releases prior to 20.1R2-EVO. This issue does not affect Juniper Networks Junos OS releases prior to 17.3R1.
CVSS Score
7.5
EPSS Score
0.004
Published
2020-07-17
When DNS filtering is enabled on Juniper Networks Junos MX Series with one of the following cards MS-PIC, MS-MIC or MS-MPC, an incoming stream of packets processed by the Multiservices PIC Management Daemon (mspmand) process, responsible for managing "URL Filtering service", may crash, causing the Services PIC to restart. While the Services PIC is restarting, all PIC services including DNS filtering service (DNS sink holing) will be bypassed until the Services PIC completes its boot process. If the issue occurs, system core-dumps output will show a crash of mspmand process: root@device> show system core-dumps -rw-rw---- 1 nobody wheel 575685123 <Date> /var/tmp/pics/mspmand.core.<*>.gz This issue affects Juniper Networks Junos OS: 17.3 versions prior to 17.3R3-S8; 18.3 versions prior to 18.3R2-S4, 18.3R3-S1; 18.4 versions prior to 18.4R2-S5, 18.4R3; 19.1 versions prior to 19.1R2-S2, 19.1R3; 19.2 versions prior to 19.2R1-S5, 19.2R2; 19.3 versions prior to 19.3R2-S3, 19.3R3; 19.4 versions prior to 19.4R1-S3, 19.4R2. This issue does not affect Juniper Networks Junos OS releases prior to 17.3R2.
CVSS Score
8.3
EPSS Score
0.003
Published
2020-07-17