The DHCPv6 Relay-Agent service, part of the Juniper Enhanced jdhcpd daemon shipped with Juniper Networks Junos OS has an Improper Input Validation vulnerability which will result in a Denial of Service (DoS) condition when a DHCPv6 client sends a specific DHPCv6 message allowing an attacker to potentially perform a Remote Code Execution (RCE) attack on the target device. Continuous receipt of the specific DHCPv6 client message will result in an extended Denial of Service (DoS) condition. If adjacent devices are also configured to relay DHCP packets, and are not affected by this issue and simply transparently forward unprocessed client DHCPv6 messages, then the attack vector can be a Network-based attack, instead of an Adjacent-device attack. No other DHCP services are affected. Receipt of the packet without configuration of the DHCPv6 Relay-Agent service, will not result in exploitability of this issue. This issue affects Juniper Networks Junos OS: 12.3 versions prior to 12.3R12-S15; 12.3X48 versions prior to 12.3X48-D95; 14.1X53 versions prior to 14.1X53-D53; 15.1 versions prior to 15.1R7-S6; 15.1X49 versions prior to 15.1X49-D200; 15.1X53 versions prior to 15.1X53-D593; 16.1 versions prior to 16.1R7-S7; 16.2 versions prior to 16.2R2-S11; 17.1 versions prior to 17.1R2-S11, 17.1R3-S2; 17.2 versions prior to 17.2R3-S3; 17.2X75 versions prior to 17.2X75-D44; 17.3 versions prior to 17.3R3-S7; 17.4 versions prior to 17.4R2-S9, 17.4R3; 18.1 versions prior to 18.1R3-S9; 18.2 versions prior to 18.2R2-S6, 18.2R3-S2; 18.2X75 versions prior to 18.2X75-D12, 18.2X75-D33, 18.2X75-D435, 18.2X75-D60; 18.3 versions prior to 18.3R1-S7, 18.3R2-S3, 18.3R3-S1; 18.4 versions prior to 18.4R1-S5, 18.4R2-S3, 18.4R3; 19.1 versions prior to 19.1R1-S4, 19.1R2; 19.2 versions prior to 19.2R1-S3, 19.2R2; 19.3 versions prior to 19.3R2.
CVSS Score
8.8
EPSS Score
0.004
Published
2020-10-16
On SRX Series devices, a vulnerability in the key-management-daemon (kmd) daemon of Juniper Networks Junos OS allows an attacker to spoof packets targeted to IPSec peers before a security association (SA) is established thereby causing a failure to set up the IPSec channel. Sustained receipt of these spoofed packets can cause a sustained Denial of Service (DoS) condition. This issue affects IPv4 and IPv6 implementations. This issue affects Juniper Networks Junos OS on SRX Series: 12.3X48 versions prior to 12.3X48-D90; 15.1X49 versions prior to 15.1X49-D190; 17.4 versions prior to 17.4R2-S9, 17.4R3; 18.1 versions prior to 18.1R3-S9; 18.2 versions prior to 18.2R3; 18.3 versions prior to 18.3R1-S7, 18.3R2-S3, 18.3R3; 18.4 versions prior to 18.4R1-S6, 18.4R2-S3, 18.4R3; 19.1 versions prior to 19.1R1-S4, 19.1R2. This issue does not affect 12.3 or 15.1 releases which are non-SRX Series releases.
CVSS Score
7.5
EPSS Score
0.004
Published
2020-10-16
When DNS filtering is enabled on Juniper Networks Junos MX Series with one of the following cards MS-PIC, MS-MIC or MS-MPC, an incoming stream of packets processed by the Multiservices PIC Management Daemon (mspmand) process, responsible for managing "URL Filtering service", may crash, causing the Services PIC to restart. While the Services PIC is restarting, all PIC services including DNS filtering service (DNS sink holing) will be bypassed until the Services PIC completes its boot process. This vulnerability might allow an attacker to cause an extended Denial of Service (DoS) attack against the device and to cause clients to be vulnerable to DNS based attacks by malicious DNS servers when they send DNS requests through the device. As a result, devices which were once protected by the DNS Filtering service are no longer protected and at risk of exploitation. This issue affects Juniper Networks Junos OS: 17.3 versions prior to 17.3R3-S8; 18.3 versions prior to 18.3R3-S1; 18.4 versions prior to 18.4R3; 19.1 versions prior to 19.1R3; 19.2 versions prior to 19.2R2; 19.3 versions prior to 19.3R3. This issue does not affect Juniper Networks Junos OS 17.4, 18.1, and 18.2.
CVSS Score
8.3
EPSS Score
0.003
Published
2020-10-16
On Juniper Networks Junos OS and Junos OS Evolved devices, BGP session flapping can lead to a routing process daemon (RPD) crash and restart, limiting the attack surface to configured BGP peers. This issue only affects devices with BGP damping in combination with accepted-prefix-limit configuration. When the issue occurs the following messages will appear in the /var/log/messages: rpd[6046]: %DAEMON-4-BGP_PREFIX_THRESH_EXCEEDED: XXXX (External AS x): Configured maximum accepted prefix-limit threshold(1800) exceeded for inet6-unicast nlri: 1984 (instance master) rpd[6046]: %DAEMON-3-BGP_CEASE_PREFIX_LIMIT_EXCEEDED: 2001:x:x:x::2 (External AS x): Shutting down peer due to exceeding configured maximum accepted prefix-limit(2000) for inet6-unicast nlri: 2001 (instance master) rpd[6046]: %DAEMON-4: bgp_rt_maxprefixes_check_common:9284: NOTIFICATION sent to 2001:x:x:x::2 (External AS x): code 6 (Cease) subcode 1 (Maximum Number of Prefixes Reached) AFI: 2 SAFI: 1 prefix limit 2000 kernel: %KERN-5: mastership_relinquish_on_process_exit: RPD crashed on master RE. Sending SIGUSR2 to chassisd (5612:chassisd) to trigger RE switchover This issue affects: Juniper Networks Junos OS: 17.2R3-S3; 17.3 version 17.3R3-S3 and later versions, prior to 17.3R3-S8; 17.4 version 17.4R2-S4, 17.4R3 and later versions, prior to 17.4R2-S10, 17.4R3-S2; 18.1 version 18.1R3-S6 and later versions, prior to 18.1R3-S10; 18.2 version 18.2R3 and later versions, prior to 18.2R3-S4; 18.2X75 version 18.2X75-D50, 18.2X75-D60 and later versions, prior to 18.2X75-D53, 18.2X75-D65; 18.3 version 18.3R2 and later versions, prior to 18.3R2-S4, 18.3R3-S2; 18.4 version 18.4R2 and later versions, prior to 18.4R2-S5, 18.4R3-S2; 19.1 version 19.1R1 and later versions, prior to 19.1R2-S2, 19.1R3-S1; 19.2 version 19.2R1 and later versions, prior to 19.2R1-S5, 19.2R2; 19.3 versions prior to 19.3R2-S3, 19.3R3; 19.4 versions prior to 19.4R1-S3, 19.4R2; 20.1 versions prior to 20.1R1-S2, 20.1R2. Juniper Networks Junos OS Evolved prior to 20.1R2-EVO. This issue does not affect Juniper Networks Junos OS versions prior to 17.2R3-S3.
CVSS Score
7.5
EPSS Score
0.006
Published
2020-10-16
A stack buffer overflow vulnerability in the device control daemon (DCD) on Juniper Networks Junos OS allows a low privilege local user to create a Denial of Service (DoS) against the daemon or execute arbitrary code in the system with root privilege. This issue affects Juniper Networks Junos OS: 17.3 versions prior to 17.3R3-S9; 17.4 versions prior to 17.4R2-S12, 17.4R3-S3; 18.1 versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S6; 18.2X75 versions prior to 18.2X75-D53, 18.2X75-D65; 18.3 versions prior to 18.3R2-S4, 18.3R3-S4; 18.4 versions prior to 18.4R2-S5, 18.4R3-S5; 19.1 versions prior to 19.1R3-S3; 19.2 versions prior to 19.2R1-S5, 19.2R3; 19.3 versions prior to 19.3R2-S4, 19.3R3; 19.4 versions prior to 19.4R1-S3, 19.4R2-S2, 19.4R3; 20.1 versions prior to 20.1R1-S4, 20.1R2; 20.2 versions prior to 20.2R1-S1, 20.2R2. Versions of Junos OS prior to 17.3 are unaffected by this vulnerability.
CVSS Score
7.8
EPSS Score
0.0
Published
2020-10-16
When DNS filtering is enabled on Juniper Networks Junos MX Series with one of the following cards MS-PIC, MS-MIC or MS-MPC, an incoming stream of packets processed by the Multiservices PIC Management Daemon (mspmand) process might be bypassed due to a race condition. Due to this vulnerability, mspmand process, responsible for managing "URL Filtering service", can crash, causing the Services PIC to restart. While the Services PIC is restarting, all PIC services including DNS filtering service (DNS sink holing) will be bypassed until the Services PIC completes its boot process. This issue affects Juniper Networks Junos OS: 17.3 versions prior to 17.3R3-S8; 18.3 versions prior to 18.3R3-S1; 18.4 versions prior to 18.4R3; 19.1 versions prior to 19.1R3; 19.2 versions prior to 19.2R2; 19.3 versions prior to 19.3R3. This issue does not affect Juniper Networks Junos OS 17.4, 18.1, and 18.2.
CVSS Score
8.3
EPSS Score
0.003
Published
2020-10-16
On Juniper Networks EX2300 Series, receipt of a stream of specific multicast packets by the layer2 interface can cause high CPU load, which could lead to traffic interruption. This issue occurs when multicast packets are received by the layer 2 interface. To check if the device has high CPU load due to this issue, the administrator can issue the following command: user@host> show chassis routing-engine Routing Engine status: ... Idle 2 percent the "Idle" value shows as low (2 % in the example above), and also the following command: user@host> show system processes summary ... PID USERNAME PRI NICE SIZE RES STATE TIME WCPU COMMAND 11639 root 52 0 283M 11296K select 12:15 44.97% eventd 11803 root 81 0 719M 239M RUN 251:12 31.98% fxpc{fxpc} the eventd and the fxpc processes might use higher WCPU percentage (respectively 44.97% and 31.98% in the above example). This issue affects Juniper Networks Junos OS on EX2300 Series: 18.1 versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S5; 18.3 versions prior to 18.3R2-S4, 18.3R3-S3; 18.4 versions prior to 18.4R2-S5, 18.4R3-S4; 19.1 versions prior to 19.1R3-S2; 19.2 versions prior to 19.2R1-S5, 19.2R3; 19.3 versions prior to 19.3R2-S4, 19.3R3; 19.4 versions prior to 19.4R1-S3, 19.4R2-S1, 19.4R3; 20.1 versions prior to 20.1R1-S2, 20.1R2.
CVSS Score
6.5
EPSS Score
0.002
Published
2020-10-16
On Juniper Networks EX4300 Series, receipt of a stream of specific IPv4 packets can cause Routing Engine (RE) high CPU load, which could lead to network protocol operation issue and traffic interruption. This specific packets can originate only from within the broadcast domain where the device is connected. This issue occurs when the packets enter to the IRB interface. Only IPv4 packets can trigger this issue. IPv6 packets cannot trigger this issue. This issue affects Juniper Networks Junos OS on EX4300 series: 17.3 versions prior to 17.3R3-S9; 17.4 versions prior to 17.4R2-S11, 17.4R3-S2; 18.1 versions prior to 18.1R3-S10; 18.2 versions prior to 18.2R3-S4; 18.3 versions prior to 18.3R2-S4, 18.3R3-S2; 18.4 versions prior to 18.4R2-S4, 18.4R3-S2; 19.1 versions prior to 19.1R2-S2, 19.1R3-S1; 19.2 versions prior to 19.2R1-S5, 19.2R2-S1, 19.2R3; 19.3 versions prior to 19.3R2-S4, 19.3R3; 19.4 versions prior to 19.4R1-S3, 19.4R2; 20.1 versions prior to 20.1R1-S3, 20.1R2.
CVSS Score
6.5
EPSS Score
0.002
Published
2020-10-16
When a device running Juniper Networks Junos OS with MPC7, MPC8, or MPC9 line cards installed and the system is configured for inline IP reassembly, used by L2TP, MAP-E, GRE, and IPIP, the packet forwarding engine (PFE) will become disabled upon receipt of large packets requiring fragmentation, generating the following error messages: [LOG: Err] MQSS(0): WO: Packet Error - Error Packets 1, Connection 29 [LOG: Err] eachip_hmcif_rx_intr_handler(7259): EA[0:0]: HMCIF Rx: Injected checksum error detected on WO response - Chunk Address 0x0 [LOG: Err] MQSS(0): DRD: RORD1: CMD reorder ID error - Command 11, Reorder ID 1838, QID 0 [LOG: Err] MQSS(0): DRD: UNROLL0: HMC chunk length error in stage 5 - Chunk Address: 0x4321f3 [LOG: Err] MQSS(0): DRD: UNROLL0: HMC chunk address error in stage 5 - Chunk Address: 0x0 [LOG: Notice] Error: /fpc/8/pfe/0/cm/0/MQSS(0)/0/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc), scope: pfe, category: functional, severity: major, module: MQSS(0), type: DRD_RORD_ENG_INT: CMD FSM State Error [LOG: Notice] Performing action cmalarm for error /fpc/8/pfe/0/cm/0/MQSS(0)/0/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(0) with scope: pfe category: functional level: major [LOG: Notice] Performing action get-state for error /fpc/8/pfe/0/cm/0/MQSS(0)/0/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(0) with scope: pfe category: functional level: major [LOG: Notice] Performing action disable-pfe for error /fpc/8/pfe/0/cm/0/MQSS(0)/0/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(0) with scope: pfe category: functional level: major By continuously sending fragmented packets that cannot be reassembled, an attacker can repeatedly disable the PFE causing a sustained Denial of Service (DoS). This issue affects Juniper Networks Junos OS: 17.2 versions prior to 17.2R3-S4 on MX Series; 17.3 versions prior to 17.3R3-S8 on MX Series; 17.4 versions prior to 17.4R2-S10, 17.4R3-S2 on MX Series; 18.1 versions prior to 18.1R3-S10 on MX Series; 18.2 versions prior to 18.2R3-S3 on MX Series; 18.2X75 versions prior to 18.2X75-D41, 18.2X75-D430, 18.2X75-D65 on MX Series; 18.3 versions prior to 18.3R1-S7, 18.3R2-S4, 18.3R3-S1 on MX Series; 18.4 versions prior to 18.4R1-S7, 18.4R2-S4, 18.4R3 on MX Series; 19.1 versions prior to 19.1R1-S5, 19.1R2-S1, 19.1R3 on MX Series; 19.2 versions prior to 19.2R1-S4, 19.2R2 on MX Series; 19.3 versions prior to 19.3R2-S2, 19.3R3 on MX Series. This issue is specific to inline IP reassembly, introduced in Junos OS 17.2. Versions of Junos OS prior to 17.2 are unaffected by this vulnerability.
CVSS Score
5.3
EPSS Score
0.003
Published
2020-07-17
On Juniper Networks SRX Series with ICAP (Internet Content Adaptation Protocol) redirect service enabled, a double free vulnerability can lead to a Denial of Service (DoS) or Remote Code Execution (RCE) due to processing of a specific HTTP message. Continued processing of this specific HTTP message may result in an extended Denial of Service (DoS). The offending HTTP message that causes this issue may originate both from the HTTP server or the client. This issue affects Juniper Networks Junos OS on SRX Series: 18.1 versions prior to 18.1R3-S9; 18.2 versions prior to 18.2R3-S3; 18.3 versions prior to 18.3R2-S4, 18.3R3-S1; 18.4 versions prior to 18.4R2-S5, 18.4R3; 19.1 versions prior to 19.1R2; 19.2 versions prior to 19.2R1-S2, 19.2R2; 19.3 versions prior to 19.3R2. This issue does not affect Juniper Networks Junos OS prior to 18.1R1.
CVSS Score
9.8
EPSS Score
0.02
Published
2020-07-17