A signal handler race condition exists in the Layer 2 Address Learning Daemon (L2ALD) of Juniper Networks Junos OS due to the absence of a specific protection mechanism to avoid a race condition which may allow an attacker to bypass the storm-control feature on devices. This issue is a corner case and only occurs during specific actions taken by an administrator of a device under certain specifics actions which triggers the event. The event occurs less frequently on devices which are not configured with Virtual Chassis configurations, and more frequently on devices configured in Virtual Chassis configurations. This issue is not specific to any particular Junos OS platform. An Indicator of Compromise (IoC) may be seen by reviewing log files for the following error message seen by executing the following show statement: show log messages | grep storm Result to look for: /kernel: GENCFG: op 58 (Storm Control Blob) failed; err 1 (Unknown) This issue affects: Juniper Networks Junos OS: 14.1X53 versions prior to 14.1X53-D49 on EX Series; 15.1 versions prior to 15.1R7-S6; 15.1X49 versions prior to 15.1X49-D191, 15.1X49-D200 on SRX Series; 16.1 versions prior to 16.1R7-S7; 16.2 versions prior to 16.2R2-S11, 16.2R3; 17.1 versions prior to 17.1R2-S11, 17.1R3; 17.2 versions prior to 17.2R2-S8, 17.2R3-S3; 17.3 versions prior to 17.3R2-S5, 17.3R3-S7; 17.4 versions prior to 17.4R2-S9, 17.4R3; 18.1 versions prior to 18.1R3-S5; 18.2 versions prior to 18.2R2-S6, 18.2R3; 18.3 versions prior to 18.3R1-S7, 18.3R2-S3, 18.3R3; 18.4 versions prior to 18.4R1-S5, 18.4R2; 19.1 versions prior to 19.1R1-S4, 19.1R2.
CVSS Score
7.4
EPSS Score
0.002
Published
2021-04-22
A Use of Hard-coded Credentials vulnerability in Juniper Networks Junos OS on Junos Fusion satellite devices allows an attacker who is local to the device to elevate their privileges and take control of the device. This issue affects: Juniper Networks Junos OS Junos Fusion Satellite Devices. 16.1 versions prior to 16.1R7-S7; 17.1 versions prior to 17.1R2-S12, 17.1R3-S2; 17.2 versions prior to 17.2R3-S4; 17.3 versions prior to 17.3R3-S8; 17.4 versions prior to 17.4R2-S10; 17.4 version 17.4R3 and later versions; 18.1 versions prior to 18.1R3-S10; 18.2 versions prior to 18.2R2-S7, 18.2R3-S3; 18.3 versions prior to 18.3R1-S7, 18.3R2-S4, 18.3R3-S2; 18.4 versions prior to 18.4R1-S6, 18.4R2-S4, 18.4R3-S1; 19.1 versions prior to 19.1R1-S5, 19.1R2-S1, 19.1R3; 19.2 versions prior to 19.2R1-S4, 19.2R2; 19.3 versions prior to 19.3R2-S5, 19.3R3; 19.4 versions prior to 19.4R1-S1, 19.4R2; 20.1 versions prior to 20.1R1-S1, 20.1R2. This issue does not affected Junos OS releases prior to 16.1R1 or all 19.2R3 and 19.4R3 release versions.
CVSS Score
7.8
EPSS Score
0.0
Published
2021-04-22
A Race Condition (Concurrent Execution using Shared Resource with Improper Synchronization) vulnerability in the firewall process (dfwd) of Juniper Networks Junos OS allows an attacker to bypass the firewall rule sets applied to the input loopback filter on any interfaces of a device. This issue is detectable by reviewing the PFE firewall rules, as well as the firewall counters and seeing if they are incrementing or not. For example: show firewall Filter: __default_bpdu_filter__ Filter: FILTER-INET-01 Counters: Name Bytes Packets output-match-inet 0 0 <<<<<< missing firewall packet count This issue affects: Juniper Networks Junos OS 14.1X53 versions prior to 14.1X53-D53 on QFX Series; 14.1 versions 14.1R1 and later versions prior to 15.1 versions prior to 15.1R7-S6 on QFX Series, PTX Series; 15.1X53 versions prior to 15.1X53-D593 on QFX Series; 16.1 versions prior to 16.1R7-S7 on QFX Series, PTX Series; 16.2 versions prior to 16.2R2-S11, 16.2R3 on QFX Series, PTX Series; 17.1 versions prior to 17.1R2-S11, 17.1R3-S2 on QFX Series, PTX Series; 17.2 versions prior to 17.2R1-S9, 17.2R3-S3 on QFX Series, PTX Series; 17.3 versions prior to 17.3R2-S5, 17.3R3-S7 on QFX Series, PTX Series; 17.4 versions prior to 17.4R2-S9, 17.4R3 on QFX Series, PTX Series; 18.1 versions prior to 18.1R3-S9 on QFX Series, PTX Series; 18.2 versions prior to 18.2R2-S6, 18.2R3-S3 on QFX Series, PTX Series; 18.3 versions prior to 18.3R1-S7, 18.3R2-S3, 18.3R3-S1 on QFX Series, PTX Series; 18.4 versions prior to 18.4R1-S5, 18.4R2-S3, 18.4R2-S7, 18.4R3 on QFX Series, PTX Series; 19.1 versions prior to 19.1R1-S4, 19.1R2-S1, 19.1R3 on QFX Series, PTX Series; 19.2 versions prior to 19.2R1-S3, 19.2R2 on QFX Series, PTX Series.
CVSS Score
5.1
EPSS Score
0.002
Published
2021-04-22
This issue is not applicable to NFX NextGen Software. On NFX Series devices the use of Hard-coded Credentials in Juniper Networks Junos OS allows an attacker to take over any instance of an NFX deployment. This issue is only exploitable through administrative interfaces. This issue affects: Juniper Networks Junos OS versions prior to 19.1R1 on NFX Series. No other platforms besides NFX Series devices are affected.
CVSS Score
10.0
EPSS Score
0.004
Published
2021-04-22
An uncontrolled resource consumption vulnerability in Message Queue Telemetry Transport (MQTT) server of Juniper Networks Junos OS allows an attacker to cause MQTT server to crash and restart leading to a Denial of Service (DoS) by sending a stream of specific packets. A Juniper Extension Toolkit (JET) application designed with a listening port uses the Message Queue Telemetry Transport (MQTT) protocol to connect to a mosquitto broker that is running on Junos OS to subscribe for events. Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. This issue affects Juniper Networks Junos OS: 16.1R1 and later versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R2-S13, 17.4R3-S4; 18.1 versions prior to 18.1R3-S12; 18.2 versions prior to 18.2R2-S8, 18.2R3-S7; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R1-S8, 18.4R2-S7, 18.4R3-S7; 19.1 versions prior to 19.1R3-S5; 19.2 versions prior to 19.2R1-S6, 19.2R3-S2; 19.3 versions prior to 19.3R3-S2; 19.4 versions prior to 19.4R2-S4, 19.4R3-S2; 20.1 versions prior to 20.1R2-S1, 20.1R3; 20.2 versions prior to 20.2R2-S2, 20.2R3; 20.3 versions prior to 20.3R1-S1, 20.3R2. This issue does not affect Juniper Networks Junos OS versions prior to 16.1R1.
CVSS Score
5.3
EPSS Score
0.005
Published
2021-04-22
On Juniper Networks SRX Series devices with link aggregation (lag) configured, executing any operation that fetches Aggregated Ethernet (AE) interface statistics, including but not limited to SNMP GET requests, causes a slow kernel memory leak. If all the available memory is consumed, the traffic will be impacted and a reboot might be required. The following log can be seen if this issue happens. /kernel: rt_pfe_veto: Memory over consumed. Op 1 err 12, rtsm_id 0:-1, msg type 72 /kernel: rt_pfe_veto: free kmem_map memory = (20770816) curproc = kmd An administrator can use the following CLI command to monitor the status of memory consumption (ifstat bucket): user@device > show system virtual-memory no-forwarding | match ifstat Type InUse MemUse HighUse Limit Requests Limit Limit Size(s) ifstat 2588977 162708K - 19633958 <<<< user@device > show system virtual-memory no-forwarding | match ifstat Type InUse MemUse HighUse Limit Requests Limit Limit Size(s) ifstat 3021629 189749K - 22914415 <<<< This issue affects Juniper Networks Junos OS on SRX Series: 17.1 versions 17.1R3 and above prior to 17.3R3-S11; 17.4 versions prior to 17.4R3-S5; 18.2 versions prior to 18.2R3-S7, 18.2R3-S8; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R2-S7, 18.4R3-S6; 19.1 versions prior to 19.1R3-S4; 19.2 versions prior to 19.2R1-S6; 19.3 versions prior to 19.3R3-S1; 19.4 versions prior to 19.4R3-S1; 20.1 versions prior to 20.1R2, 20.1R3; 20.2 versions prior to 20.2R2-S2, 20.2R3; 20.3 versions prior to 20.3R1-S2, 20.3R2. This issue does not affect Juniper Networks Junos OS prior to 17.1R3.
CVSS Score
7.5
EPSS Score
0.004
Published
2021-04-22
A vulnerability in Juniper Networks Junos OS allows an attacker to cause a Denial of Service (DoS) to the device by sending certain crafted protocol packets from an adjacent device with invalid payloads to the device. These crafted packets, which should be discarded, are instead replicated and sent to the RE. Over time, a Denial of Service (DoS) occurs. Continued receipt of these crafted protocol packets will cause an extended Denial of Service (DoS) condition, which may cause wider traffic impact due to protocol flapping. An indication of compromise is to check "monitor interface traffic" on the ingress and egress port packet counts. For each ingress packet, two duplicate packets are seen on egress. This issue can be triggered by IPv4 and IPv6 packets. This issue affects all traffic through the device. This issue affects: Juniper Networks Junos OS: 14.1X53 versions prior to 14.1X53-D53 on EX4300, QFX3500, QFX5100, EX4600; 15.1 versions prior to 15.1R7-S6 on EX4300, QFX3500, QFX5100, EX4600; 16.1 versions prior to 16.1R7-S7 on EX4300, QFX5100, EX4600; 17.1 versions prior to 17.1R2-S11 on EX4300, QFX5100, EX4600; 17.1 versions prior to 117.1R3-S2 on EX4300; 17.2 versions prior to 17.2R1-S9 on EX4300; 17.2 versions prior to 17.2R3-S3 on EX4300, QFX5100, EX4600, QFX5110, QFX5200; 17.3 versions prior to 17.3R2-S5, 17.3R3-S7 on EX4300, QFX5100, EX4600, QFX5110, QFX5200; 17.4 versions prior to 17.4R2-S9, 17.4R3 on EX4300, QFX5100, EX4600, QFX5110, QFX5200; 18.1 versions prior to 18.1R3-S9 on EX4300, QFX5100, EX4600, QFX5110, QFX5200, QFX5210, EX2300, EX3400; 18.2 versions prior to 18.2R2-S7 on EX4300; 18.2 versions prior to 18.2R3-S3 on EX4300, QFX5100, EX4600, QFX5110, QFX5200, QFX5210, EX2300, EX3400; 18.3 versions prior to 18.3R2-S3, on EX4300; 18.3 versions prior to 18.3R1-S7, 18.3R3-S1 on EX4300, QFX5100, EX4600, QFX5110, QFX5200, QFX5210, QFX5120, EX4650, EX2300, EX3400; 18.4 versions prior to 18.4R1-S5, 18.4R2-S3, 18.4R3 on EX4300, QFX5100, EX4600, QFX5110, QFX5200, QFX5210, QFX5120, EX4650, EX2300, EX3400; 19.1 versions prior to 19.1R1-S4, 19.1R2-S1, 19.1R3 on EX4300, QFX5100, EX4600, QFX5110, QFX5200, QFX5210, QFX5120, EX4650, EX2300, EX3400; 19.2 versions prior to 19.2R1-S4, 19.2R2 on EX4300; 19.2 versions prior to 19.2R1-S3, 19.2R2 on QFX5100, EX4600, QFX5110, QFX5200, QFX5210, QFX5120, EX4650, EX2300, EX3400; 19.3 versions prior to 19.3R2-S1, 19.3R3 on EX4300; 19.3 versions prior to 19.3R1-S1, 19.3R2, 19.3R3 on QFX5100, EX4600, QFX5110, QFX5200, QFX5210, QFX5120, EX4650, EX2300, EX3400;
CVSS Score
7.4
EPSS Score
0.001
Published
2021-01-15
The DHCPv6 Relay-Agent service, part of the Juniper Enhanced jdhcpd daemon shipped with Juniper Networks Junos OS has an Improper Input Validation vulnerability which will result in a Denial of Service (DoS) condition when a DHCPv6 client sends a specific DHPCv6 message allowing an attacker to potentially perform a Remote Code Execution (RCE) attack on the target device. Continuous receipt of the specific DHCPv6 client message will result in an extended Denial of Service (DoS) condition. If adjacent devices are also configured to relay DHCP packets, and are not affected by this issue and simply transparently forward unprocessed client DHCPv6 messages, then the attack vector can be a Network-based attack, instead of an Adjacent-device attack. No other DHCP services are affected. Receipt of the packet without configuration of the DHCPv6 Relay-Agent service, will not result in exploitability of this issue. This issue affects Juniper Networks Junos OS: 12.3 versions prior to 12.3R12-S15; 12.3X48 versions prior to 12.3X48-D95; 14.1X53 versions prior to 14.1X53-D53; 15.1 versions prior to 15.1R7-S6; 15.1X49 versions prior to 15.1X49-D200; 15.1X53 versions prior to 15.1X53-D593; 16.1 versions prior to 16.1R7-S7; 16.2 versions prior to 16.2R2-S11; 17.1 versions prior to 17.1R2-S11, 17.1R3-S2; 17.2 versions prior to 17.2R3-S3; 17.2X75 versions prior to 17.2X75-D44; 17.3 versions prior to 17.3R3-S7; 17.4 versions prior to 17.4R2-S9, 17.4R3; 18.1 versions prior to 18.1R3-S9; 18.2 versions prior to 18.2R2-S6, 18.2R3-S2; 18.2X75 versions prior to 18.2X75-D12, 18.2X75-D33, 18.2X75-D435, 18.2X75-D60; 18.3 versions prior to 18.3R1-S7, 18.3R2-S3, 18.3R3-S1; 18.4 versions prior to 18.4R1-S5, 18.4R2-S3, 18.4R3; 19.1 versions prior to 19.1R1-S4, 19.1R2; 19.2 versions prior to 19.2R1-S3, 19.2R2; 19.3 versions prior to 19.3R2.
CVSS Score
8.8
EPSS Score
0.004
Published
2020-10-16
A Race Condition vulnerability in Juniper Networks Junos OS LLDP implementation allows an attacker to cause LLDP to crash leading to a Denial of Service (DoS). This issue occurs when crafted LLDP packets are received by the device from an adjacent device. Multiple LACP flaps will occur after LLDP crashes. An indicator of compromise is to evaluate log file details for lldp with RLIMIT. Intervention should occur before 85% threshold of used KB versus maximum available KB memory is reached. show log messages | match RLIMIT | match lldp | last 20 Matching statement is " /kernel: %KERNEL-[number]: Process ([pid #],lldpd) has exceeded 85% of RLIMIT_DATA: " with [] as variable data to evaluate for. This issue affects: Juniper Networks Junos OS: 12.3 versions prior to 12.3R12-S15; 12.3X48 versions prior to 12.3X48-D95; 15.1 versions prior to 15.1R7-S6; 15.1X49 versions prior to 15.1X49-D200; 15.1X53 versions prior to 15.1X53-D593; 16.1 versions prior to 16.1R7-S7; 17.1 versions prior to 17.1R2-S11, 17.1R3-S2; 17.2 versions prior to 17.2R1-S9, 17.2R3-S3; 17.3 versions prior to 17.3R2-S5, 17.3R3-S6; 17.4 versions prior to 17.4R2-S4, 17.4R3; 18.1 versions prior to 18.1R3-S5; 18.2 versions prior to 18.2R2-S7, 18.2R3; 18.2X75 versions prior to 18.2X75-D12, 18.2X75-D33, 18.2X75-D50, 18.2X75-D420; 18.3 versions prior to 18.3R1-S7, 18.3R2-S3, 18.3R3; 18.4 versions prior to 18.4R1-S5, 18.4R2; 19.1 versions prior to 19.1R1-S4, 19.1R2.
CVSS Score
6.5
EPSS Score
0.001
Published
2020-07-17
Execution of the "show ospf interface extensive" or "show ospf interface detail" CLI commands on a Juniper Networks device running Junos OS may cause the routing protocols process (RPD) to crash and restart if OSPF interface authentication is configured, leading to a Denial of Service (DoS). By continuously executing the same CLI commands, a local attacker can repeatedly crash the RPD process causing a sustained Denial of Service. Note: Only systems utilizing ARM processors, found on the EX2300 and EX3400, are vulnerable to this issue. Systems shipped with other processor architectures are not vulnerable to this issue. The processor architecture can be displayed via the 'uname -a' command. For example: ARM (vulnerable): % uname -a | awk '{print $NF}' arm PowerPC (not vulnerable): % uname -a | awk '{print $NF}' powerpc AMD (not vulnerable): % uname -a | awk '{print $NF}' amd64 Intel (not vulnerable): % uname -a | awk '{print $NF}' i386 This issue affects Juniper Networks Junos OS: 12.3X48 versions prior to 12.3X48-D100; 14.1X53 versions prior to 14.1X53-D140, 14.1X53-D54; 15.1 versions prior to 15.1R7-S7; 15.1X49 versions prior to 15.1X49-D210; 15.1X53 versions prior to 15.1X53-D593; 16.1 versions prior to 16.1R7-S8; 17.1 versions prior to 17.1R2-S12; 17.2 versions prior to 17.2R3-S4; 17.3 versions prior to 17.3R3-S8; 17.4 versions prior to 17.4R2-S2, 17.4R3; 18.1 versions prior to 18.1R3-S2; 18.2 versions prior to 18.2R2, 18.2R3; 18.2X75 versions prior to 18.2X75-D40; 18.3 versions prior to 18.3R1-S2, 18.3R2.
CVSS Score
5.5
EPSS Score
0.001
Published
2020-07-17