Zephyrproject: >> Zephyr >> 4.4.2 Security Vulnerabilities
In the Synopsys DesignWare I2C driver (drivers/i2c/i2c_dw.c) operating in target/slave mode, the rx_full interrupt handler gates the write_requested() callback on dw->state != CMD_SEND, and dw->state is only reset to READY on a STOP interrupt. The START_DET interrupt, whose handler in i2c_dw_slave_read_clear_intr_bits() would reset the state on every (re)START, was never added to the enabled interrupt mask in i2c_dw_slave_register(), so that recovery path was dead code.
As a result, if the STOP interrupt is lost (bus glitch/reset, or a concurrent master driving STOP) or the bus master issues a legal WRITE-repeated-START-WRITE sequence with the same direction, the driver remains in CMD_SEND permanently and never invokes write_requested() again for the life of the target.
An I2C master on the same physical bus can deliberately trigger this, causing the I2C target function to malfunction for all subsequent write transactions and desynchronizing consumer framing state (e.g. MCTP-over-I2C), a recoverable-by-reset denial of service of the target peripheral.
The fix unmasks START_DET so the state is reset at every bus (re)START. Impact is availability-only over a local board-level bus; no memory corruption results in the in-tree consumer, whose per-byte buffer write is independently bounds-checked.
CVSS Score
2.4
EPSS Score
0.002
Published
2026-07-27
In Zephyr's userspace dynamic-objects subsystem, thread_idx_alloc() in kernel/userspace/userspace.c allocated a new thread permission index from the global _thread_idx_map[] bitmap without holding lists_lock.
On SMP systems, two user-mode threads invoking the k_object_alloc(K_OBJ_THREAD) syscall concurrently can both observe the same low free bit, perform the same non-atomic RMW to clear it, and return the identical tidx.
The two newly created K_OBJ_THREAD objects are then assigned the same thread_id, so the two user threads alias a single bit position in every kernel object's perms[] bitfield: any subsequent grant of access on a kernel object to one thread is implicitly a grant to the other, defeating userspace ACL isolation. A secondary lost-update window between the unlocked &=~BIT() in alloc and the locked |= BIT() in thread_idx_free() can also leak entries from the thread-index pool.
The defect is reachable from any user-mode thread via the unrestricted __syscall k_object_alloc and is gated on CONFIG_USERSPACE, CONFIG_DYNAMIC_OBJECTS, and CONFIG_SMP. The flaw was introduced when the per-thread permission index was added in 2018 and is present in every release up to and including v4.4.0. Fixed by holding lists_lock across the bitmap RMW and the permissions clear (and inlining the obj_list traversal that previously took the lock itself).
CVSS Score
6.5
EPSS Score
0.001
Published
2026-07-25
The Zephyr ext2 file system validates the on-disk superblock in ext2_verify_disk_superblock() (subsys/fs/ext2/ext2_impl.c) before completing a mount. The validator checked the magic number, block size, revision and feature flags, but did not verify that the on-disk fields s_blocks_per_group and s_inodes_per_group are non-zero. Both fields are read directly from the image and are later used as divisors during mount-time initialization.
During mount, get_ngroups() divides and modulos s_blocks_count by s_blocks_per_group (reached via ext2_fetch_block_group() from ext2_init_fs()), and get_itable_entry() divides (ino - 1) by s_inodes_per_group when fetching the root inode (both in subsys/fs/ext2/ext2_diskops.c). A superblock with either field set to zero therefore causes an integer division by zero during the mount sequence.
An attacker who can present a crafted ext2 image to a device that mounts ext2 — removable media such as an SD card or a USB mass-storage device — can trigger this. On ARMv7-M / ARMv8-M-mainline Cortex-M targets, divide-by-zero trapping is enabled (SCB_CCR_DIV_0_TRP), so the division raises a UsageFault that Zephyr treats as a fatal error, producing a denial of service. The impact is limited to availability; the malformed value is consumed only as a divisor.
The fix rejects a zero s_blocks_per_group or s_inodes_per_group in the superblock validator, returning -EINVAL so the mount fails before any block-group or inode I/O occurs.
CVSS Score
4.6
EPSS Score
0.002
Published
2026-07-24
The Zephyr ADIN2111/ADIN1110 10BASE-T1S/T1L Ethernet driver (drivers/ethernet/eth_adin2111.c) reassembles received Ethernet frames in OPEN Alliance (OA) SPI mode by copying device-supplied 64-byte data chunks into a fixed static buffer ctx->buf of size CONFIG_ETH_ADIN2111_BUFFER_SIZE (default 1524 bytes). In eth_adin2111_oa_data_read(), each valid chunk was memcpy'd into ctx->buf[ctx->scur] and the write cursor scur advanced, with no check that scur + len stayed within the buffer. The number of chunks (up to 255, from the BUFSTS RCA field) and the per-chunk length are taken entirely from the frame data received off the wire; the cursor is only reset on a start-of-frame chunk. An attacker on the single-pair Ethernet segment can therefore send a frame whose reassembled size exceeds the configured buffer, causing the driver's RX offload thread to write attacker-controlled frame bytes past the end of the static buffer into adjacent driver/kernel memory (up to roughly 14.8 KB in the worst case). This is a remotely/adjacently reachable out-of-bounds write (CWE-787) that can corrupt memory and cause denial of service or potentially code execution. The defect was introduced when OA SPI support was added (commit 0ca8b0756b1) and shipped in releases v3.7.0 through v4.4.0. The fix adds a bounds check that drops the oversized frame and resets the cursor before the copy.
CVSS Score
8.3
EPSS Score
0.004
Published
2026-07-15
On Xtensa SoCs built with CONFIG_XTENSA_MPU and CONFIG_USERSPACE, arch_buffer_validate() in arch/xtensa/core/mpu.c — the architecture hook that verifies a user-mode-supplied buffer is accessible to the calling user thread with the requested permission — defaulted its return value to 0 (access permitted) and only set a denial result inside its per-MPU-region probe loop. When the rounded extent of the buffer wraps the 32-bit address space (size + alignment offset near SIZE_MAX, or ROUND_UP(size + offset) overflowing to 0), the loop executes zero iterations and the function returns 0 = permitted without probing any MPU region.
The syscall-layer pre-checks (K_SYSCALL_MEMORY_SIZE_CHECK / Z_DETECT_POINTER_OVERFLOW) only catch a raw addr+size wrap and do not cover the ROUND_UP-induced wrap, and the string path (arch_user_string_nlen -> arch_buffer_validate) has no syscall-layer guard at all.
An unprivileged user-mode thread can therefore pass a crafted (addr, size) to any syscall that validates user buffers via k_usermode_from_copy/to_copy or k_usermode_string_copy and have validation succeed for memory it must not access; the kernel then reads from (disclosure) or, with write=1, writes to (corruption) attacker-chosen kernel or other-partition memory on the thread's behalf, enabling information disclosure, memory corruption, privilege escalation, and denial of service.
Affected from v3.7.0 (when Xtensa MPU userspace support was added) through v4.4.0. The fix changes the default to -EINVAL (deny by default), adds an explicit size_add_overflow check, and sets the success value only after the full range has been validated.
CVSS Score
7.8
EPSS Score
0.002
Published
2026-07-14
The CONFIG_USERSPACE verification handler for the k_thread_name_copy() system call (z_vrfy_k_thread_name_copy() in kernel/thread.c) calls k_object_find() on the caller-supplied thread pointer and then dereferences the returned struct k_object without checking it for NULL. k_object_find() returns NULL whenever the supplied pointer is not a registered (static or dynamic) kernel object.
The pre-fix guard tested thread == NULL instead of ko == NULL, so an unprivileged user-mode thread that invokes k_thread_name_copy() with any non-NULL but unregistered pointer (e.g. an arbitrary address) passes the NULL test, after which the verifier reads ko->type through a NULL pointer.
Because the syscall verifier runs in supervisor mode, this NULL dereference is a kernel-mode fault that halts or reboots the system, allowing untrusted user code to crash the kernel across the userspace security boundary (denial of service). The marshaller passes the thread argument to the verifier without any prior K_SYSCALL_OBJ validation, so the bad pointer reaches the defect directly.
The flaw affects builds with CONFIG_USERSPACE and CONFIG_THREAD_NAME enabled and has been present since the special-case lookup was introduced around v2.0.0; it is present in v4.4.0 and earlier. The fix changes the guard to check the k_object_find() return value (ko == NULL) before dereferencing it.
CVSS Score
5.5
EPSS Score
0.002
Published
2026-07-14
In Zephyr's kernel pipe implementation, the userspace syscall verifier z_vrfy_k_pipe_init() in kernel/pipe.c used K_SYSCALL_OBJ() (which requires the kernel object to already be initialized) instead of K_SYSCALL_OBJ_NEVER_INIT() (which rejects an already-initialized object). As a result, on CONFIG_USERSPACE builds an unprivileged user thread that has been granted access to a k_pipe object can invoke the k_pipe_init syscall to re-initialize a pipe that is already in use.
z_impl_k_pipe_init() unconditionally resets the ring buffer, sets pipe->waiting to 0, and re-initializes both wait queues (z_waitq_init on pipe->data and pipe->space) without waking or accounting for threads currently blocked on the pipe. Any thread already pended in k_pipe_read()/k_pipe_write() is left orphaned: still marked pending with pended_on pointing at the cleared wait queue and with stale qnode_dlist links into the (now re-initialized) embedded list head.
When such an orphaned waiter is later timed out or woken, the scheduler calls sys_dlist_remove() on its stale node, writing through dangling prev/next pointers into kernel wait-queue/scheduler structures, causing list corruption (an attacker-driven invalid kernel write), lost wakeups, indefinitely blocked threads, and silent data loss. The flaw lets a deprivileged user thread corrupt the state of a kernel object shared with other threads/partitions.
The fix switches the verifier to K_SYSCALL_OBJ_NEVER_INIT(), matching the existing k_msgq_init verifier, so a user thread can no longer re-initialize a live pipe. The vulnerable code shipped in v4.1.0 and remained through v4.4.0.
CVSS Score
7.1
EPSS Score
0.002
Published
2026-07-14
The nRF70 Wi-Fi driver's power-save event handler nrf_wifi_event_proc_get_power_save_info() in drivers/wifi/nrf_wifi/src/wifi_mgmt.c copied TWT (Target Wake Time) flow entries from an nrf_wifi_umac_event_power_save_info event into the fixed-size twt_flows[WIFI_MAX_TWT_FLOWS] (8-element) array of a caller-supplied struct wifi_ps_config, looping over event-provided num_twt_flows without validating it against WIFI_MAX_TWT_FLOWS or checking event_len. When num_twt_flows exceeds 8, the handler writes past the destination array (which is typically on the caller's stack, e.g. the wifi ps shell command) -- an out-of-bounds write of ~40-byte TWT entries -- and reads twt_flow_info[i] past the event buffer. The event is delivered by the nRF70 co-processor firmware in response to a host-initiated power-save GET, so reaching the overflow requires the firmware to emit a malformed or out-of-range event; the trust boundary is host-to-trusted-coprocessor rather than a direct remote-AP write, with over-the-air influence on the flow count being indirect and bounded by the 3-bit TWT flow-id space. Affected: builds with CONFIG_NRF70_STA_MODE on releases through v4.4.0. The fix rejects events with num_twt_flows > WIFI_MAX_TWT_FLOWS or with event_len shorter than the claimed entries, and adds a NULL check on the caller buffer.
CVSS Score
5.0
EPSS Score
0.002
Published
2026-07-12
In Zephyr's experimental USB host stack (CONFIG_USB_HOST_STACK), usbh_device_disconnect() (subsys/usb/host/usbh_device.c) freed the root usb_device slab object without clearing the cached pointer ctx->root. The bus removal handler dev_removed_handler() (subsys/usb/host/usbh_core.c) decides what to tear down solely from ctx->root, checking only that it is non-NULL.
Because UHC controller drivers (e.g. uhc_max3421e, uhc_mcux_common) synthesize UHC_EVT_DEV_REMOVED directly from physical bus line state with no debounce or state guard, an attacker with physical USB access (or a rogue device that bounces its connection) can deliver a second device-removed event after a root device disconnect. The handler then re-enters usbh_device_disconnect() with the dangling pointer, locking a mutex inside the freed object (use-after-free), removing the freed node from the device list, and calling k_mem_slab_free() on the already-freed block (double-free). If the slab block has been reissued to a newly attached device in between, this corrupts a live object.
Impact is denial of service (crash) and memory corruption; the attack vector is physical/local. The flaw was introduced in v4.4.0 by the connect/disconnect refactor and is fixed by clearing ctx->root in usbh_device_disconnect() before freeing.
CVSS Score
6.1
EPSS Score
0.002
Published
2026-07-12
The USB CDC-NCM device class (subsys/usb/device_next/class/usbd_cdc_ncm.c) ignores the return value of usbd_ep_enqueue() in its ethernet transmit callback cdc_ncm_send(). When the enqueue fails, the function still calls k_sem_take(&data->sync_sem, K_FOREVER), blocking on a completion semaphore that is only ever signaled from the bulk-IN transfer-completion callback. Because nothing was enqueued, that callback never fires and the calling thread — a shared network traffic-class TX thread — deadlocks permanently while holding the interface TX lock, halting transmission until reboot (and leaking the transmit buffer).
The enqueue fails under conditions controlled by the attached USB host: usbd_ep_enqueue() returns -EPERM whenever the bus is suspended (a standard, persistent host operation), and the underlying udc_ep_enqueue() returns -EPERM/-ENODEV on disconnect, bus reset, or endpoint disable. The cdc_ncm_send() guard only checks the DATA_IFACE_ENABLED and IFACE_UP flags, not the suspended state, so a packet transmitted while the host holds the bus suspended reaches the failing enqueue and deadlocks the TX path.
The realistic trigger is a bus suspend that occurs while the exported network interface is active and has traffic to send — host sleep, USB selective/auto-suspend, or hub power management — after which any device-originated packet deadlocks the path, recoverable only by reboot. The impact is a persistent loss of the virtual network connection between the host's NCM interface and the Zephyr device; because the deadlocked thread is a shared traffic-class TX thread, egress on other network interfaces can stall as well. There is no memory corruption or information disclosure.
The defect was introduced with the CDC-NCM driver and shipped in releases through v4.4.0; it is fixed by checking the usbd_ep_enqueue() return value and freeing the buffer before the blocking wait.
CVSS Score
5.3
EPSS Score
0.002
Published
2026-06-29