A vulnerability in ICMP Version 6 (ICMPv6) processing in Cisco NX-OS Software could allow an unauthenticated, remote attacker to cause a slow system memory leak, which over time could lead to a denial of service (DoS) condition. This vulnerability is due to improper error handling when an IPv6-configured interface receives a specific type of ICMPv6 packet. An attacker could exploit this vulnerability by sending a sustained rate of crafted ICMPv6 packets to a local IPv6 address on a targeted device. A successful exploit could allow the attacker to cause a system memory leak in the ICMPv6 process on the device. As a result, the ICMPv6 process could run out of system memory and stop processing traffic. The device could then drop all ICMPv6 packets, causing traffic instability on the device. Restoring device functionality would require a device reboot.
A vulnerability in the Border Gateway Protocol (BGP) Multicast VPN (MVPN) implementation of Cisco NX-OS Software could allow an unauthenticated, remote attacker to cause a BGP session to repeatedly reset, causing a partial denial of service (DoS) condition due to the BGP session being down. The vulnerability is due to incorrect parsing of a specific type of BGP MVPN update message. An attacker could exploit this vulnerability by sending this BGP MVPN update message to a targeted device. A successful exploit could allow the attacker to cause the BGP peer connections to reset, which could lead to BGP route instability and impact traffic. The incoming BGP MVPN update message is valid but is parsed incorrectly by the NX-OS device, which could send a corrupted BGP update to the configured BGP peer. Note: The Cisco implementation of BGP accepts incoming BGP traffic from only explicitly configured peers. To exploit this vulnerability, an attacker must send a specific BGP MVPN update message over an established TCP connection that appears to come from a trusted BGP peer. To do so, the attacker must obtain information about the BGP peers in the trusted network of the affected system.
A vulnerability in the Call Home feature of Cisco NX-OS Software could allow an authenticated, remote attacker to inject arbitrary commands that could be executed with root privileges on the underlying operating system (OS). The vulnerability is due to insufficient input validation of specific Call Home configuration parameters when the software is configured for transport method HTTP. An attacker could exploit this vulnerability by modifying parameters within the Call Home configuration on an affected device. A successful exploit could allow the attacker to execute arbitrary commands with root privileges on the underlying OS.
A vulnerability in the local management (local-mgmt) CLI of Cisco UCS Manager Software could allow an authenticated, local attacker to cause a denial of service (DoS) condition on an affected device. The vulnerability is due to improper handling of CLI command parameters. An attacker could exploit this vulnerability by executing specific commands on the local-mgmt CLI on an affected device. A successful exploit could allow the attacker to cause internal system processes to fail to terminate properly, which could result in a buildup of stuck processes and lead to slowness in accessing the UCS Manager CLI and web UI. A sustained attack may result in a restart of internal UCS Manager processes and a temporary loss of access to the UCS Manager CLI and web UI.
A vulnerability in the Cisco Fabric Services component of Cisco FXOS Software and Cisco NX-OS Software could allow an unauthenticated attacker to cause process crashes, which could result in a denial of service (DoS) condition on an affected device. The attack vector is configuration dependent and could be remote or adjacent. For more information about the attack vector, see the Details section of this advisory. The vulnerability is due to insufficient error handling when the affected software parses Cisco Fabric Services messages. An attacker could exploit this vulnerability by sending malicious Cisco Fabric Services messages to an affected device. A successful exploit could allow the attacker to cause a reload of an affected device, which could result in a DoS condition.
A vulnerability in the Protocol Independent Multicast (PIM) feature for IPv6 networks (PIM6) of Cisco NX-OS Software could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition on an affected device. The vulnerability is due to improper error handling when processing inbound PIM6 packets. An attacker could exploit this vulnerability by sending multiple crafted PIM6 packets to an affected device. A successful exploit could allow the attacker to cause the PIM6 application to leak system memory. Over time, this memory leak could cause the PIM6 application to stop processing legitimate PIM6 traffic, leading to a DoS condition on the affected device.
IP-in-IP protocol specifies IP Encapsulation within IP standard (RFC 2003, STD 1) that decapsulate and route IP-in-IP traffic is vulnerable to spoofing, access-control bypass and other unexpected behavior due to the lack of validation to verify network packets before decapsulation and routing.
A vulnerability in the NX-API feature of Cisco NX-OS Software could allow an unauthenticated, remote attacker to cause an NX-API system process to unexpectedly restart. The vulnerability is due to incorrect validation of the HTTP header of a request that is sent to the NX-API. An attacker could exploit this vulnerability by sending a crafted HTTP request to the NX-API on an affected device. A successful exploit could allow the attacker to cause a denial of service (DoS) condition in the NX-API service; however, the Cisco NX-OS device itself would still be available and passing network traffic. Note: The NX-API feature is disabled by default.
A vulnerability in the Cisco Discovery Protocol feature of Cisco FXOS Software and Cisco NX-OS Software could allow an unauthenticated, adjacent attacker to execute arbitrary code as root or cause a denial of service (DoS) condition on an affected device. The vulnerability exists because of insufficiently validated Cisco Discovery Protocol packet headers. An attacker could exploit this vulnerability by sending a crafted Cisco Discovery Protocol packet to a Layer 2-adjacent affected device. A successful exploit could allow the attacker to cause a buffer overflow that could allow the attacker to execute arbitrary code as root or cause a DoS condition on the affected device. Note: Cisco Discovery Protocol is a Layer 2 protocol. To exploit this vulnerability, an attacker must be in the same broadcast domain as the affected device (Layer 2 adjacent). Note: This vulnerability is different from the following Cisco FXOS and NX-OS Software Cisco Discovery Protocol vulnerabilities that Cisco announced on Feb. 5, 2020: Cisco FXOS, IOS XR, and NX-OS Software Cisco Discovery Protocol Denial of Service Vulnerability and Cisco NX-OS Software Cisco Discovery Protocol Remote Code Execution Vulnerability.
A vulnerability in the anycast gateway feature of Cisco NX-OS Software could allow an unauthenticated, adjacent attacker to cause a device to learn invalid Address Resolution Protocol (ARP) entries. The ARP entries are for nonlocal IP addresses for the subnet. The vulnerability is due to improper validation of a received gratuitous ARP (GARP) request. An attacker could exploit this vulnerability by sending a malicious GARP packet on the local subnet to cause the ARP table on the device to become corrupted. A successful exploit could allow the attacker to populate the ARP table with incorrect entries, which could lead to traffic disruptions.