Linux: >> Linux Kernel >> 5.4.278 Security Vulnerabilities
In the Linux kernel, the following vulnerability has been resolved:
fbdev: au1200fb: Fix a memory leak in au1200fb_drv_probe()
In au1200fb_drv_probe(), when platform_get_irq fails(), it directly
returns from the function with an error code, which causes a memory
leak.
Replace it with a goto label to ensure proper cleanup.
CVSS Score
5.5
EPSS Score
0.001
Published
2026-05-27
In the Linux kernel, the following vulnerability has been resolved:
iommu/vt-d: Clear Present bit before tearing down context entry
When tearing down a context entry, the current implementation zeros the
entire 128-bit entry using multiple 64-bit writes. This creates a window
where the hardware can fetch a "torn" entry — where some fields are
already zeroed while the 'Present' bit is still set — leading to
unpredictable behavior or spurious faults.
While x86 provides strong write ordering, the compiler may reorder writes
to the two 64-bit halves of the context entry. Even without compiler
reordering, the hardware fetch is not guaranteed to be atomic with
respect to multiple CPU writes.
Align with the "Guidance to Software for Invalidations" in the VT-d spec
(Section 6.5.3.3) by implementing the recommended ownership handshake:
1. Clear only the 'Present' (P) bit of the context entry first to
signal the transition of ownership from hardware to software.
2. Use dma_wmb() to ensure the cleared bit is visible to the IOMMU.
3. Perform the required cache and context-cache invalidation to ensure
hardware no longer has cached references to the entry.
4. Fully zero out the entry only after the invalidation is complete.
Also, add a dma_wmb() to context_set_present() to ensure the entry
is fully initialized before the 'Present' bit becomes visible.
CVSS Score
7.5
EPSS Score
0.001
Published
2026-05-27
In the Linux kernel, the following vulnerability has been resolved:
net: stmmac: fix oops when split header is enabled
For GMAC4, when split header is enabled, in some rare cases, the
hardware does not fill buf2 of the first descriptor with payload.
Thus we cannot assume buf2 is always fully filled if it is not
the last descriptor. Otherwise, the length of buf2 of the second
descriptor will be calculated wrong and cause an oops:
Unable to handle kernel paging request at virtual address ffff00019246bfc0
...
x2 : 0000000000000040 x1 : ffff00019246bfc0 x0 : ffff00009246c000
Call trace:
dcache_inval_poc+0x28/0x58 (P)
dma_direct_sync_single_for_cpu+0x38/0x6c
__dma_sync_single_for_cpu+0x34/0x6c
stmmac_napi_poll_rx+0x8f0/0xb60
__napi_poll.constprop.0+0x30/0x144
net_rx_action+0x160/0x274
handle_softirqs+0x1b8/0x1fc
...
To fix this, the PL bit-field in RDES3 register is used for all
descriptors, whether it is the last descriptor or not.
CVSS Score
5.5
EPSS Score
0.002
Published
2026-05-27
In the Linux kernel, the following vulnerability has been resolved:
tpm: tpm_i2c_infineon: Fix locality leak on get_burstcount() failure
get_burstcount() can return -EBUSY on timeout. When this happens, the
function returns directly without releasing the locality that was
acquired at the beginning of tpm_tis_i2c_send().
Use goto out_err to ensure proper cleanup when get_burstcount() fails.
CVSS Score
5.5
EPSS Score
0.001
Published
2026-05-27
In the Linux kernel, the following vulnerability has been resolved:
ext4: fix e4b bitmap inconsistency reports
A bitmap inconsistency issue was observed during stress tests under
mixed huge-page workloads. Ext4 reported multiple e4b bitmap check
failures like:
ext4_mb_complex_scan_group:2508: group 350, 8179 free clusters as
per group info. But got 8192 blocks
Analysis and experimentation confirmed that the issue is caused by a
race condition between page migration and bitmap modification. Although
this timing window is extremely narrow, it is still hit in practice:
folio_lock ext4_mb_load_buddy
__migrate_folio
check ref count
folio_mc_copy __filemap_get_folio
folio_try_get(folio)
......
mb_mark_used
ext4_mb_unload_buddy
__folio_migrate_mapping
folio_ref_freeze
folio_unlock
The root cause of this issue is that the fast path of load_buddy only
increments the folio's reference count, which is insufficient to prevent
concurrent folio migration. We observed that the folio migration process
acquires the folio lock. Therefore, we can determine whether to take the
fast path in load_buddy by checking the lock status. If the folio is
locked, we opt for the slow path (which acquires the lock) to close this
concurrency window.
Additionally, this change addresses the following issues:
When the DOUBLE_CHECK macro is enabled to inspect bitmap-related
issues, the following error may be triggered:
corruption in group 324 at byte 784(6272): f in copy != ff on
disk/prealloc
Analysis reveals that this is a false positive. There is a specific race
window where the bitmap and the group descriptor become momentarily
inconsistent, leading to this error report:
ext4_mb_load_buddy ext4_mb_load_buddy
__filemap_get_folio(create|lock)
folio_lock
ext4_mb_init_cache
folio_mark_uptodate
__filemap_get_folio(no lock)
......
mb_mark_used
mb_mark_used_double
mb_cmp_bitmaps
mb_set_bits(e4b->bd_bitmap)
folio_unlock
The original logic assumed that since mb_cmp_bitmaps is called when the
bitmap is newly loaded from disk, the folio lock would be sufficient to
prevent concurrent access. However, this overlooks a specific race
condition: if another process attempts to load buddy and finds the folio
is already in an uptodate state, it will immediately begin using it without
holding folio lock.
CVSS Score
7.8
EPSS Score
0.001
Published
2026-05-27
In the Linux kernel, the following vulnerability has been resolved:
btrfs: fix EEXIST abort due to non-consecutive gaps in chunk allocation
I have been observing a number of systems aborting at
insert_dev_extents() in btrfs_create_pending_block_groups(). The
following is a sample stack trace of such an abort coming from forced
chunk allocation (typically behind CONFIG_BTRFS_EXPERIMENTAL) but this
can theoretically happen to any DUP chunk allocation.
[81.801] ------------[ cut here ]------------
[81.801] BTRFS: Transaction aborted (error -17)
[81.801] WARNING: fs/btrfs/block-group.c:2876 at btrfs_create_pending_block_groups+0x721/0x770 [btrfs], CPU#1: bash/319
[81.802] Modules linked in: virtio_net btrfs xor zstd_compress raid6_pq null_blk
[81.803] CPU: 1 UID: 0 PID: 319 Comm: bash Kdump: loaded Not tainted 6.19.0-rc6+ #319 NONE
[81.803] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Arch Linux 1.17.0-2-2 04/01/2014
[81.804] RIP: 0010:btrfs_create_pending_block_groups+0x723/0x770 [btrfs]
[81.806] RSP: 0018:ffffa36241a6bce8 EFLAGS: 00010282
[81.806] RAX: 000000000000000d RBX: ffff8e699921e400 RCX: 0000000000000000
[81.807] RDX: 0000000002040001 RSI: 00000000ffffffef RDI: ffffffffc0608bf0
[81.807] RBP: 00000000ffffffef R08: ffff8e69830f6000 R09: 0000000000000007
[81.808] R10: ffff8e699921e5e8 R11: 0000000000000000 R12: ffff8e6999228000
[81.808] R13: ffff8e6984d82000 R14: ffff8e69966a69c0 R15: ffff8e69aa47b000
[81.809] FS: 00007fec6bdd9740(0000) GS:ffff8e6b1b379000(0000) knlGS:0000000000000000
[81.809] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[81.810] CR2: 00005604833670f0 CR3: 0000000116679000 CR4: 00000000000006f0
[81.810] Call Trace:
[81.810] <TASK>
[81.810] __btrfs_end_transaction+0x3e/0x2b0 [btrfs]
[81.811] btrfs_force_chunk_alloc_store+0xcd/0x140 [btrfs]
[81.811] kernfs_fop_write_iter+0x15f/0x240
[81.812] vfs_write+0x264/0x500
[81.812] ksys_write+0x6c/0xe0
[81.812] do_syscall_64+0x66/0x770
[81.812] entry_SYSCALL_64_after_hwframe+0x76/0x7e
[81.813] RIP: 0033:0x7fec6be66197
[81.814] RSP: 002b:00007fffb159dd30 EFLAGS: 00000202 ORIG_RAX: 0000000000000001
[81.815] RAX: ffffffffffffffda RBX: 00007fec6bdd9740 RCX: 00007fec6be66197
[81.815] RDX: 0000000000000002 RSI: 0000560483374f80 RDI: 0000000000000001
[81.816] RBP: 0000560483374f80 R08: 0000000000000000 R09: 0000000000000000
[81.816] R10: 0000000000000000 R11: 0000000000000202 R12: 0000000000000002
[81.817] R13: 00007fec6bfb85c0 R14: 00007fec6bfb5ee0 R15: 00005604833729c0
[81.817] </TASK>
[81.817] irq event stamp: 20039
[81.818] hardirqs last enabled at (20047): [<ffffffff99a68302>] __up_console_sem+0x52/0x60
[81.818] hardirqs last disabled at (20056): [<ffffffff99a682e7>] __up_console_sem+0x37/0x60
[81.819] softirqs last enabled at (19470): [<ffffffff999d2b46>] __irq_exit_rcu+0x96/0xc0
[81.819] softirqs last disabled at (19463): [<ffffffff999d2b46>] __irq_exit_rcu+0x96/0xc0
[81.820] ---[ end trace 0000000000000000 ]---
[81.820] BTRFS: error (device dm-7 state A) in btrfs_create_pending_block_groups:2876: errno=-17 Object already exists
Inspecting these aborts with drgn, I observed a pattern of overlapping
chunk_maps. Note how stripe 1 of the first chunk overlaps in physical
address with stripe 0 of the second chunk.
Physical Start Physical End Length Logical Type Stripe
----------------------------------------------------------------------------------------------------
0x0000000102500000 0x0000000142500000 1.0G 0x0000000641d00000 META|DUP 0/2
0x0000000142500000 0x0000000182500000 1.0G 0x0000000641d00000 META|DUP 1/2
0x0000000142500000 0x0000000182500000 1.0G 0x0000000601d00000 META|DUP 0/2
0x0000000182500000 0x00000001c2500000 1.0G 0x0000000601d00000 META|DUP 1/2
Now how could this possibly happen? All chunk allocation is
---truncated---
CVSS Score
5.5
EPSS Score
0.001
Published
2026-05-27
In the Linux kernel, the following vulnerability has been resolved:
power: supply: goldfish: Fix use-after-free in power_supply_changed()
Using the `devm_` variant for requesting IRQ _before_ the `devm_`
variant for allocating/registering the `power_supply` handle, means that
the `power_supply` handle will be deallocated/unregistered _before_ the
interrupt handler (since `devm_` naturally deallocates in reverse
allocation order). This means that during removal, there is a race
condition where an interrupt can fire just _after_ the `power_supply`
handle has been freed, *but* just _before_ the corresponding
unregistration of the IRQ handler has run.
This will lead to the IRQ handler calling `power_supply_changed()` with
a freed `power_supply` handle. Which usually crashes the system or
otherwise silently corrupts the memory...
Note that there is a similar situation which can also happen during
`probe()`; the possibility of an interrupt firing _before_ registering
the `power_supply` handle. This would then lead to the nasty situation
of using the `power_supply` handle *uninitialized* in
`power_supply_changed()`.
Fix this racy use-after-free by making sure the IRQ is requested _after_
the registration of the `power_supply` handle.
CVSS Score
7.8
EPSS Score
0.001
Published
2026-05-27
In the Linux kernel, the following vulnerability has been resolved:
net: usb: catc: enable basic endpoint checking
catc_probe() fills three URBs with hardcoded endpoint pipes without
verifying the endpoint descriptors:
- usb_sndbulkpipe(usbdev, 1) and usb_rcvbulkpipe(usbdev, 1) for TX/RX
- usb_rcvintpipe(usbdev, 2) for interrupt status
A malformed USB device can present these endpoints with transfer types
that differ from what the driver assumes.
Add a catc_usb_ep enum for endpoint numbers, replacing magic constants
throughout. Add usb_check_bulk_endpoints() and usb_check_int_endpoints()
calls after usb_set_interface() to verify endpoint types before use,
rejecting devices with mismatched descriptors at probe time.
Similar to
- commit 90b7f2961798 ("net: usb: rtl8150: enable basic endpoint checking")
which fixed the issue in rtl8150.
CVSS Score
5.5
EPSS Score
0.002
Published
2026-05-27
In the Linux kernel, the following vulnerability has been resolved:
fat: avoid parent link count underflow in rmdir
Corrupted FAT images can leave a directory inode with an incorrect
i_nlink (e.g. 2 even though subdirectories exist). rmdir then
unconditionally calls drop_nlink(dir) and can drive i_nlink to 0,
triggering the WARN_ON in drop_nlink().
Add a sanity check in vfat_rmdir() and msdos_rmdir(): only drop the
parent link count when it is at least 3, otherwise report a filesystem
error.
CVSS Score
5.5
EPSS Score
0.002
Published
2026-05-27
In the Linux kernel, the following vulnerability has been resolved:
power: supply: sbs-battery: Fix use-after-free in power_supply_changed()
Using the `devm_` variant for requesting IRQ _before_ the `devm_`
variant for allocating/registering the `power_supply` handle, means that
the `power_supply` handle will be deallocated/unregistered _before_ the
interrupt handler (since `devm_` naturally deallocates in reverse
allocation order). This means that during removal, there is a race
condition where an interrupt can fire just _after_ the `power_supply`
handle has been freed, *but* just _before_ the corresponding
unregistration of the IRQ handler has run.
This will lead to the IRQ handler calling `power_supply_changed()` with
a freed `power_supply` handle. Which usually crashes the system or
otherwise silently corrupts the memory...
Note that there is a similar situation which can also happen during
`probe()`; the possibility of an interrupt firing _before_ registering
the `power_supply` handle. This would then lead to the nasty situation
of using the `power_supply` handle *uninitialized* in
`power_supply_changed()`.
Fix this racy use-after-free by making sure the IRQ is requested _after_
the registration of the `power_supply` handle. Keep the old behavior of
just printing a warning in case of any failures during the IRQ request
and finishing the probe successfully.
CVSS Score
7.8
EPSS Score
0.002
Published
2026-05-27