In the Linux kernel, the following vulnerability has been resolved:
wifi: brcmsmac: add gain range check to wlc_phy_iqcal_gainparams_nphy()
In 'wlc_phy_iqcal_gainparams_nphy()', add gain range check to WARN()
instead of possible out-of-bounds 'tbl_iqcal_gainparams_nphy' access.
Compile tested only.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
In the Linux kernel, the following vulnerability has been resolved:
safesetid: check size of policy writes
syzbot attempts to write a buffer with a large size to a sysfs entry
with writes handled by handle_policy_update(), triggering a warning
in kmalloc.
Check the size specified for write buffers before allocating.
[PM: subject tweak]
In the Linux kernel, the following vulnerability has been resolved:
printk: Fix signed integer overflow when defining LOG_BUF_LEN_MAX
Shifting 1 << 31 on a 32-bit int causes signed integer overflow, which
leads to undefined behavior. To prevent this, cast 1 to u32 before
performing the shift, ensuring well-defined behavior.
This change explicitly avoids any potential overflow by ensuring that
the shift occurs on an unsigned 32-bit integer.
In the Linux kernel, the following vulnerability has been resolved:
HID: multitouch: Add NULL check in mt_input_configured
devm_kasprintf() can return a NULL pointer on failure,but this
returned value in mt_input_configured() is not checked.
Add NULL check in mt_input_configured(), to handle kernel NULL
pointer dereference error.
In the Linux kernel, the following vulnerability has been resolved:
ocfs2: handle a symlink read error correctly
Patch series "Convert ocfs2 to use folios".
Mark did a conversion of ocfs2 to use folios and sent it to me as a
giant patch for review ;-)
So I've redone it as individual patches, and credited Mark for the patches
where his code is substantially the same. It's not a bad way to do it;
his patch had some bugs and my patches had some bugs. Hopefully all our
bugs were different from each other. And hopefully Mark likes all the
changes I made to his code!
This patch (of 23):
If we can't read the buffer, be sure to unlock the page before returning.
In the Linux kernel, the following vulnerability has been resolved:
media: uvcvideo: Remove dangling pointers
When an async control is written, we copy a pointer to the file handle
that started the operation. That pointer will be used when the device is
done. Which could be anytime in the future.
If the user closes that file descriptor, its structure will be freed,
and there will be one dangling pointer per pending async control, that
the driver will try to use.
Clean all the dangling pointers during release().
To avoid adding a performance penalty in the most common case (no async
operation), a counter has been introduced with some logic to make sure
that it is properly handled.
In the Linux kernel, the following vulnerability has been resolved:
PCI: dwc: ep: Prevent changing BAR size/flags in pci_epc_set_bar()
In commit 4284c88fff0e ("PCI: designware-ep: Allow pci_epc_set_bar() update
inbound map address") set_bar() was modified to support dynamically
changing the backing physical address of a BAR that was already configured.
This means that set_bar() can be called twice, without ever calling
clear_bar() (as calling clear_bar() would clear the BAR's PCI address
assigned by the host).
This can only be done if the new BAR size/flags does not differ from the
existing BAR configuration. Add these missing checks.
If we allow set_bar() to set e.g. a new BAR size that differs from the
existing BAR size, the new address translation range will be smaller than
the BAR size already determined by the host, which would mean that a read
past the new BAR size would pass the iATU untranslated, which could allow
the host to read memory not belonging to the new struct pci_epf_bar.
While at it, add comments which clarifies the support for dynamically
changing the physical address of a BAR. (Which was also missing.)
In the Linux kernel, the following vulnerability has been resolved:
soc: qcom: socinfo: Avoid out of bounds read of serial number
On MSM8916 devices, the serial number exposed in sysfs is constant and does
not change across individual devices. It's always:
db410c:/sys/devices/soc0$ cat serial_number
2644893864
The firmware used on MSM8916 exposes SOCINFO_VERSION(0, 8), which does not
have support for the serial_num field in the socinfo struct. There is an
existing check to avoid exposing the serial number in that case, but it's
not correct: When checking the item_size returned by SMEM, we need to make
sure the *end* of the serial_num is within bounds, instead of comparing
with the *start* offset. The serial_number currently exposed on MSM8916
devices is just an out of bounds read of whatever comes after the socinfo
struct in SMEM.
Fix this by changing offsetof() to offsetofend(), so that the size of the
field is also taken into account.