In the Linux kernel, the following vulnerability has been resolved:
Revert "fs/ntfs3: Replace inode_trylock with inode_lock"
This reverts commit 69505fe98f198ee813898cbcaf6770949636430b.
Initially, conditional lock acquisition was removed to fix an xfstest bug
that was observed during internal testing. The deadlock reported by syzbot
is resolved by reintroducing conditional acquisition. The xfstest bug no
longer occurs on kernel version 6.16-rc1 during internal testing. I
assume that changes in other modules may have contributed to this.
In the Linux kernel, the following vulnerability has been resolved:
NFS: Fix filehandle bounds checking in nfs_fh_to_dentry()
The function needs to check the minimal filehandle length before it can
access the embedded filehandle.
In the Linux kernel, the following vulnerability has been resolved:
serial: 8250: fix panic due to PSLVERR
When the PSLVERR_RESP_EN parameter is set to 1, the device generates
an error response if an attempt is made to read an empty RBR (Receive
Buffer Register) while the FIFO is enabled.
In serial8250_do_startup(), calling serial_port_out(port, UART_LCR,
UART_LCR_WLEN8) triggers dw8250_check_lcr(), which invokes
dw8250_force_idle() and serial8250_clear_and_reinit_fifos(). The latter
function enables the FIFO via serial_out(p, UART_FCR, p->fcr).
Execution proceeds to the serial_port_in(port, UART_RX).
This satisfies the PSLVERR trigger condition.
When another CPU (e.g., using printk()) is accessing the UART (UART
is busy), the current CPU fails the check (value & ~UART_LCR_SPAR) ==
(lcr & ~UART_LCR_SPAR) in dw8250_check_lcr(), causing it to enter
dw8250_force_idle().
Put serial_port_out(port, UART_LCR, UART_LCR_WLEN8) under the port->lock
to fix this issue.
Panic backtrace:
[ 0.442336] Oops - unknown exception [#1]
[ 0.442343] epc : dw8250_serial_in32+0x1e/0x4a
[ 0.442351] ra : serial8250_do_startup+0x2c8/0x88e
...
[ 0.442416] console_on_rootfs+0x26/0x70
In the Linux kernel, the following vulnerability has been resolved:
parisc: Revise __get_user() to probe user read access
Because of the way read access support is implemented, read access
interruptions are only triggered at privilege levels 2 and 3. The
kernel executes at privilege level 0, so __get_user() never triggers
a read access interruption (code 26). Thus, it is currently possible
for user code to access a read protected address via a system call.
Fix this by probing read access rights at privilege level 3 (PRIV_USER)
and setting __gu_err to -EFAULT (-14) if access isn't allowed.
Note the cmpiclr instruction does a 32-bit compare because COND macro
doesn't work inside asm.
In the Linux kernel, the following vulnerability has been resolved:
vsock/virtio: Validate length in packet header before skb_put()
When receiving a vsock packet in the guest, only the virtqueue buffer
size is validated prior to virtio_vsock_skb_rx_put(). Unfortunately,
virtio_vsock_skb_rx_put() uses the length from the packet header as the
length argument to skb_put(), potentially resulting in SKB overflow if
the host has gone wonky.
Validate the length as advertised by the packet header before calling
virtio_vsock_skb_rx_put().
In the Linux kernel, the following vulnerability has been resolved:
iio: imu: bno055: fix OOB access of hw_xlate array
Fix a potential out-of-bounds array access of the hw_xlate array in
bno055.c.
In bno055_get_regmask(), hw_xlate was iterated over the length of the
vals array instead of the length of the hw_xlate array. In the case of
bno055_gyr_scale, the vals array is larger than the hw_xlate array,
so this could result in an out-of-bounds access. In practice, this
shouldn't happen though because a match should always be found which
breaks out of the for loop before it iterates beyond the end of the
hw_xlate array.
By adding a new hw_xlate_len field to the bno055_sysfs_attr, we can be
sure we are iterating over the correct length.
In the Linux kernel, the following vulnerability has been resolved:
media: venus: protect against spurious interrupts during probe
Make sure the interrupt handler is initialized before the interrupt is
registered.
If the IRQ is registered before hfi_create(), it's possible that an
interrupt fires before the handler setup is complete, leading to a NULL
dereference.
This error condition has been observed during system boot on Rb3Gen2.
In the Linux kernel, the following vulnerability has been resolved:
media: venus: Add a check for packet size after reading from shared memory
Add a check to ensure that the packet size does not exceed the number of
available words after reading the packet header from shared memory. This
ensures that the size provided by the firmware is safe to process and
prevent potential out-of-bounds memory access.
In the Linux kernel, the following vulnerability has been resolved:
media: rainshadow-cec: fix TOCTOU race condition in rain_interrupt()
In the interrupt handler rain_interrupt(), the buffer full check on
rain->buf_len is performed before acquiring rain->buf_lock. This
creates a Time-of-Check to Time-of-Use (TOCTOU) race condition, as
rain->buf_len is concurrently accessed and modified in the work
handler rain_irq_work_handler() under the same lock.
Multiple interrupt invocations can race, with each reading buf_len
before it becomes full and then proceeding. This can lead to both
interrupts attempting to write to the buffer, incrementing buf_len
beyond its capacity (DATA_SIZE) and causing a buffer overflow.
Fix this bug by moving the spin_lock() to before the buffer full
check. This ensures that the check and the subsequent buffer modification
are performed atomically, preventing the race condition. An corresponding
spin_unlock() is added to the overflow path to correctly release the
lock.
This possible bug was found by an experimental static analysis tool
developed by our team.