Zephyrproject: >> Zephyr >> 2.82.0 Security Vulnerabilities
The MCUmgr SMP-over-console transport decodes a base64 frame, reads a 16-bit packet length from it, verifies a CRC and then unconditionally strips the trailing CRC with rx_ctxt->nb->len -= 2U; in mcumgr_serial_process_frag() (subsys/mgmt/mcumgr/transport/src/serial_util.c). mcumgr_serial_extract_len() accepted any declared length, including 0 and 1, and a packet declaring length 0 passes the checksum test for free because crc16_itu_t() over zero bytes returns the zero seed. Since net_buf::len is a uint16_t, the subtraction underflows and the buffer is handed to SMP claiming roughly 65 KB of payload while its data area is only CONFIG_MCUMGR_TRANSPORT_NETBUF_SIZE bytes (default 384).
The trigger is a single unauthenticated 7-byte line on the management console — the 0x06 0x09 packet marker followed by the base64 group AAA= and a newline — delivered to any transport built on this helper: CONFIG_MCUMGR_TRANSPORT_UART (smp_uart.c) or CONFIG_MCUMGR_TRANSPORT_SHELL (smp_shell.c), both of which select MCUMGR_TRANSPORT_SERIAL_HAS_SMP_OVER_CONSOLE. No prior session state, fragmentation or credentials are required to trigger the underflow, and the malformed frame is mishandled before any command handler or command-level access control runs. The attacker only needs write access to that console, which on many boards is a USB CDC-ACM port rather than a bare UART header.
With the inflated length, smp_process_request_packet() in subsys/mgmt/mcumgr/smp/src/smp.c loses its bound: cbor_nb_reader_init() gives the CBOR decoder a ~65 KB window into a 384-byte buffer, and each request header's nh_len is checked only against the inflated length. On its own the 7-byte frame re-parses whatever stale bytes the reused pool buffer still holds, typically a replay of the previously received request followed by a parse error, without leaving the buffer. Because the transport is unauthenticated, though, the attacker also controls the frames sent before the trigger, and can stage buffer contents so that a request succeeds with an nh_len larger than the buffer; net_buf_pull(), guarded only by __ASSERT_NO_MSG, then moves the parse cursor out of bounds and the loop reads further headers and CBOR from adjacent memory. The consequence is an out-of-bounds read that can fault the MCUmgr thread (denial of service); memory disclosure is also possible, since the default-enabled os echo handler (CONFIG_MCUMGR_GRP_OS_ECHO) decodes its string inside that window and copies it into its response. There is no integrity gain beyond what the unauthenticated transport already permits.
The fix rejects any declared packet length of two bytes or fewer in mcumgr_serial_extract_len(), so the CRC-strip subtraction can no longer underflow. The identical pattern remains in the test-only loopback transport subsys/mgmt/mcumgr/transport/src/smp_dummy.c (CONFIG_MCUMGR_TRANSPORT_DUMMY), which has no external input path and therefore carries no practical exposure.
CVSS Score
6.8
EPSS Score
0.002
Published
2026-09-29
The CoAP link-format helper match_path_uri() in subsys/net/lib/coap/coap_link_format.c compares a registered resource path against the URI carried in a Uri-Query href= option. That URI is not NUL terminated, but the inner character loop advanced its index k once per path character without ever testing it against the option length len. When a registered path segment is longer than the supplied URI and the URI is a prefix of it, the loop reads uri[len] and beyond, past the end of the option value.
The path is reached from coap_well_known_core_get_len() and coap_well_known_core_get() via match_queries_resource(), i.e. by any unauthenticated GET /.well-known/core?href=/<prefix> request to a device that serves /.well-known/core (for the CoAP server subsystem, CONFIG_COAP_SERVER_WELL_KNOWN_CORE, default y) and has at least one resource that declares struct coap_core_metadata attributes.
The over-read does not reach the receive buffer. The well-known-core builders parse the query into a stack-local struct coap_option, whose value is a fixed array (value[12], or CONFIG_COAP_EXTENDED_OPTIONS_LEN_VALUE bytes) that the option bytes are copied into, so uri points into that copy. Reading past len therefore reads the unused, uninitialized tail of the array and, when the option fills it, the bytes just past it in the same stack frame. (In the ZoAP library of v1.8.0 to v1.9.x the option value was instead a pointer into the received packet, and the over-read ran past the option inside the packet buffer.)
The impact is bounded. The number of bytes read past the end is limited by the length of the resource path segment, and each additional byte is only read if it happens to equal the next path character, so in practice the over-read is one byte. It also cannot influence the response: returning a match requires the final compared index to be len - 1 or len, both in bounds, so out-of-bounds bytes only ever steer the loop to the next candidate resource. The consequence is undefined behaviour, not information disclosure and not a matching error.
The fix adds a k >= len guard at the top of the inner loop, so every uri[k] dereference is within the option value while still allowing a trailing * wildcard to match a longer path.
CVSS Score
3.7
EPSS Score
0.002
Published
2026-09-28
The hawkBit device management client in subsys/mgmt/hawkbit accumulates the body of an HTTP response from the update server into a heap buffer in response_json_cb() (subsys/mgmt/hawkbit/hawkbit.c). The buffer is sized to hold the received body bytes but reserves no space for a terminating NUL. When the full response has arrived, the code writes response_data[downloaded_size] = '\0' — and whenever the accumulated body length equals the allocation, that terminator lands one byte past the end of the heap object (a heap-based out-of-bounds write, CWE-122 / CWE-787).
The body length and fragmentation are taken directly from the parsed HTTP response (rsp->body_frag_start / rsp->body_frag_len) and are fully controlled by the remote hawkBit server, which chooses its own response length. The precise trigger depends on how the buffer grows, and both forms are remotely reachable. Since v4.0.0 the reallocation is sized to exactly downloaded_size + body_len, so any response body larger than the 1100-byte initial buffer makes the out-of-bounds write deterministic; such response sizes are normal for hawkBit deployment metadata. Before v4.0.0 the buffer grew by doubling and the growth check ((downloaded_size + body_len) > response_buffer_size) is false at equality, so a response body whose length is exactly the current allocation — 1100 bytes with the default initial buffer — skips the reallocation entirely and writes the terminator at response_data[1100] of an 1100-byte object. The HTTP length-mismatch check does not catch this, because the declared and received lengths genuinely agree. Either form is reachable by a malicious, compromised, or man-in-the-middle update server (TLS is optional and, when enabled, does not protect against a hostile server), with no authentication of response content and no client-side length cap protecting the write.
The out-of-bounds write is a fixed single NUL byte immediately following the allocation, corrupting adjacent allocator metadata or the next allocation. The practical impact is heap corruption leading to denial of service (fault on a subsequent allocation or free), with the bounded, allocator-dependent possibility of further corruption. The fix sizes the buffer to the body length plus one and copies with memcpy, ensuring the terminator always lands within the allocation.
CVSS Score
8.2
EPSS Score
0.005
Published
2026-08-03
Zephyr's Bluetooth host declares a GATT characteristic as two consecutive attributes: a Characteristic Declaration whose permission is hard-coded to BT_GATT_PERM_READ, and a Characteristic Value attribute that carries the application-specified security permissions (e.g. BT_GATT_PERM_READ_ENCRYPT / READ_AUTHEN / READ_LESC). The public notify and indicate APIs explicitly accept either attribute, and passing the declaration is the documented, common idiom. Before sending each notification or indication, the host re-checks link security with bt_gatt_check_perm() against params->attr in gatt_notify(), gatt_indicate(), and gatt_notify_multiple_verify_params() (subsys/bluetooth/host/gatt.c).
When the application passed the Characteristic Declaration attribute, the host correctly redirected the value handle but left params->attr pointing at the declaration, so the security check evaluated the declaration's permissions (no security required) instead of the value's. As a result the encryption/authentication/LESC requirement configured on the characteristic value was skipped. The Notify-Multiple path additionally used a mask that omitted the LE Secure Connections requirement.
A remote peer triggers the disclosure by connecting (optionally without pairing or encryption) and writing the Client Characteristic Configuration descriptor to enable notifications or indications, causing the server to emit the protected value over a link that has not reached the required security level. The impact is information disclosure / access-control bypass for characteristic values the application intended to expose only over a secured link; exposure depends on the application declaring encrypt/authen-required notify/indicate characteristics and on the CCC being writable at a lower security tier. There is no memory-safety or availability impact.
The fix adds bt_gatt_attr_resolve_value(), which maps a declaration attribute to the following value attribute before the permission check, and switches the Notify-Multiple path to the full BT_GATT_PERM_READ_ENCRYPT_MASK so the LESC requirement is also enforced.
CVSS Score
6.5
EPSS Score
0.002
Published
2026-08-01
Zephyr's IPv6 forwarding path re-sent routed unicast packets without ever decrementing the IPv6 hop limit. Both routing branches of ipv6_route_packet() (subsys/net/ip) were affected: the explicit-route path (net_route_packet()) and the on-link cross-interface path (net_route_packet_if()). Each set the packet forwarding flag and called net_send_data() with the hop limit untouched and no expiry check.
Per RFC 8200 the hop-limit decrement is the mechanism that bounds packet lifetime and terminates routing loops; without it, a device acting as an IPv6 router relays looping packets indefinitely. An on-path attacker who can induce or exploit a transient L3 loop turns it into a permanent forwarding storm, causing CPU/bandwidth resource exhaustion (availability DoS) on the forwarder and adjacent links; path-discovery and loop diagnostics that rely on hop-limit expiry are also defeated.
Affected configurations. In every affected release the forwarding path is reached via CONFIG_NET_ROUTE (enabled by default when CONFIG_NET_IPV6_NBR_CACHE is set), together with CONFIG_NET_ROUTING for cross-interface routing. Note that CONFIG_NET_IPV6_FORWARDING and CONFIG_NET_IPV4_FORWARDING — which appear in the fix and in this advisory's evidence notes — were introduced after v4.4.0, when the routing options were split and renamed; they do not exist in any affected release. When auditing a v4.4.1-or-earlier configuration, look for CONFIG_NET_ROUTE and CONFIG_NET_ROUTING.
IPv4 is not affected in any release. The IPv4 forwarding path (net_route_ipv4_packet() in route_ipv4.c) was added after v4.4.0 and has never shipped in a release. Its TTL decrement and IPv4 header-checksum recomputation landed on main as part of the same fix, so the evidence notes below discuss it, but no released version is reachable by way of IPv4.
Affected releases are v1.8.0 through v4.4.1: v1.8.0 introduced net_route_packet() and v2.2.0 added net_route_packet_if(), and neither decremented the hop limit. v4.3.1 carries the explicit-route fix but not the on-link one, so it is affected as well. Fixed on main by 7d8f1afa7345 (explicit-route path) and 589eadc74efa (on-link path).
CVSS Score
5.8
EPSS Score
0.006
Published
2026-07-31
The Zephyr Bluetooth GATT client CCC-write response handler gatt_write_ccc_rsp() in subsys/bluetooth/host/gatt.c invoked the application's params->subscribe() callback after it had already called params->notify(conn, params, NULL, 0).
Per the public GATT API, a notify callback with NULL data is the documented signal that the subscription has terminated and the bt_gatt_subscribe_params struct may be freed or reused by the application; calling subscribe() on the struct afterwards is a use-after-free, including an indirect call through the freed params->subscribe function pointer.
The error branch is remotely (adjacent) reachable: a Zephyr device acting as a GATT client that calls bt_gatt_subscribe() can be driven into this ordering when a connected GATT server peer answers the CCC write with an ATT Error Response (the peer-supplied error code flows through att_error_rsp -> att_handle_rsp into gatt_write_ccc_rsp).
For applications that free or recycle subscription parameters in their notification-termination handler, this results in memory corruption, a crash (denial of service), or potentially attacker-influenced control flow. The fix reorders the handler so the subscribe() callback runs before the terminating notify(NULL) in both the error and unsubscribe paths.
CVSS Score
7.6
EPSS Score
0.003
Published
2026-07-31
In Zephyr's userspace dynamic-objects subsystem, thread_idx_alloc() in kernel/userspace/userspace.c allocated a new thread permission index from the global _thread_idx_map[] bitmap without holding lists_lock.
On SMP systems, two user-mode threads invoking the k_object_alloc(K_OBJ_THREAD) syscall concurrently can both observe the same low free bit, perform the same non-atomic RMW to clear it, and return the identical tidx.
The two newly created K_OBJ_THREAD objects are then assigned the same thread_id, so the two user threads alias a single bit position in every kernel object's perms[] bitfield: any subsequent grant of access on a kernel object to one thread is implicitly a grant to the other, defeating userspace ACL isolation. A secondary lost-update window between the unlocked &=~BIT() in alloc and the locked |= BIT() in thread_idx_free() can also leak entries from the thread-index pool.
The defect is reachable from any user-mode thread via the unrestricted __syscall k_object_alloc and is gated on CONFIG_USERSPACE, CONFIG_DYNAMIC_OBJECTS, and CONFIG_SMP. The flaw was introduced when the per-thread permission index was added in 2018 and is present in every release up to and including v4.4.0. Fixed by holding lists_lock across the bitmap RMW and the permissions clear (and inlining the obj_list traversal that previously took the lock itself).
CVSS Score
6.5
EPSS Score
0.001
Published
2026-07-25
The DesignWare SPI driver (drivers/spi/spi_dw.c) computed the SPI BAUDR clock divider as info->clock_frequency / config->frequency without validating config->frequency.
spi_transceive is a Zephyr __syscall and its verify handler (drivers/spi/spi_handlers.c) copies the caller-supplied spi_config from userspace without checking the frequency field, so a userspace thread that has been granted access to a DesignWare SPI device kernel object can pass frequency = 0 and trigger an unsigned integer divide-by-zero in spi_dw_configure().
On Cortex-M Mainline (SCB->CCR.DIV_0_TRP is set in z_arm_fault_init()) and on ARC (a dedicated __ev_div_zero vector) this raises a CPU exception, resulting in a kernel fault and local denial of service.
The fix rejects zero frequency and frequencies above clock_frequency / 2 (the DesignWare SSI databook minimum SCKDIV of 2) with -EINVAL. The defect affects all Zephyr releases up to and including v4.4.0; exploitation requires CONFIG_USERSPACE=y and an unprivileged thread already granted SPI driver permission. There is no memory-corruption or information-disclosure impact.
CVSS Score
3.3
EPSS Score
0.001
Published
2026-07-21
The CONFIG_USERSPACE syscall verifier z_vrfy_k_poll() in kernel/poll.c allocates a kernel-side copy of the user-supplied k_poll_event[] via z_thread_malloc() and then validates each event's object handle. Before this fix, validation used K_OOPS(K_SYSCALL_OBJ(...)) inline inside the loop, which kills the calling thread without freeing events_copy.
A user thread can pass num_events >= 1 with a forged object handle to leak the allocation; because newly spawned user threads inherit the parent's resource_pool (kernel/thread.c), an attacker spawns sacrificial threads to repeat the leak until the shared kernel heap is exhausted. Once depleted, legitimate kernel allocations from that pool (k_queue alloc nodes, k_msgq buffers, future k_poll calls, etc.) fail, causing a system-level denial of service.
The fix replaces each inline K_OOPS with a conditional goto oops_free so the buffer is freed before the thread is killed. Affects Zephyr releases from v1.12.0 (when k_poll was first exposed to user mode) through v4.4.1.
CVSS Score
6.5
EPSS Score
0.001
Published
2026-07-21
The NXP LPUART serial driver (drivers/serial/uart_mcux_lpuart.c), when CONFIG_UART_USE_RUNTIME_CONFIGURE is enabled, called LPUART_Deinit() at the start of mcux_lpuart_configure(), which disables the LPUART peripheral clocks. The requested configuration is validated only afterwards (in mcux_lpuart_configure_basic), and unsupported parity/data-bit/stop-bit/flow-control values return -ENOTSUP before the clock is re-enabled.
As a result, a uart_configure() request with an unsupported configuration left the LPUART in a clock-disabled state; any subsequent access to LPUART registers (poll_out/poll_in, interrupt handling, or a later reconfigure) faults on the gated peripheral and escalates to a hard fault, crashing the system.
uart_configure() is a Zephyr syscall whose verifier (z_vrfy_uart_configure) only checks that cfg is readable user memory and forwards the caller-supplied configuration unchanged, so an unprivileged userspace thread with access to an LPUART device can deterministically trigger the fault, a persistent system-wide denial of service.
Introduced in v2.5.0 and present in all subsequent releases until this fix, which removes the LPUART_Deinit() call and instead only disables the transmitter/receiver, leaving the clock running.
CVSS Score
5.5
EPSS Score
0.001
Published
2026-07-21
Page 1